Miele DA 1260 Operating And Installation Instructions Download | Manualshive

Page: 8 / 44

background image

IMPORTANT SAFETY INSTRUCTIONS

8



Fat and debris deposits impair the proper functioning of the

ventilation hood.
To ensure that cooking vapors are properly cleaned, never use the
ventilation hood without the grease filters in place.



There is a risk of fire if cleaning is not completed according to the

instructions in this manual.



Please note that the heat rising from the stovetop during cooking

can cause the ventilation hood to become very hot.
Do not touch the housing or the grease filters until the ventilation
hood has cooled down.

«
...
6
7
8
9
10
...
»

Summary of Contents for DA 1260













































Reviews:

No comments

Related manuals for DA 1260

Brand: Candy Pages: 26

Brand: Zanussi Pages: 20

Brand: Proline Pages: 10

Brand: Xo Pages: 25

Spruce AK9834BS

Brand: Zephyr Pages: 48

Brand: Agua Pages: 14

Brand: Gaggenau Pages: 20

Brand: U.S. Products Pages: 8

Brand: TJERNLUND Pages: 8

Brand: Smeg Pages: 10

Brand: Broan Pages: 8

Brand: Broan Pages: 8

Brand: Broan Pages: 1

Brand: Broan Pages: 36

Best ISER222 Series

Brand: Broan Pages: 2

Brand: Broan Pages: 24

Brand: Broan Pages: 36

Brand: Broan Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands