background image

Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
unauthorised work.

Various messages will appear in the
display to warn of certain problems.
Follow the instructions to remedy the
problem.

Other problems or situations which
occur in general use are described in
this section. With the help of the
following notes, minor faults in the
performance of the machine, some of
which may result from incorrect
operation, can be put right without
contacting the Service Department.

What to do if ...

... the machine does not light up after
it has been switched on.

Has the lighting been switched off?

^

If it has, switch it back on (see
"Settings: customising your machine -
Lighting").

^

If not, then the lighting is defective.
Call the Miele Service Department.

. . . nothing appears in the display.

The master switch is at "0".

^

Set the master switch to "I".

The plug is not inserted in the socket
correctly.

^

check that the plug is inserted
correctly and switched on at the
socket.

The main fuse has tripped due to a
problem with the coffee machine, the
electricity supply or another appliance.

^

Contact a qualified electrician or
Miele.

... the machine suddenly switches
itself off.

The machine will switch itself off
automatically after a certain length of
time if it is not being used. This time
depends on the

switch off time which

has been programmed

.

There could be stones in amongst the
coffee beans. If this is the case, the
machine will switch itself off
automatically within 20 seconds to
avoid damage. Call the Miele Service
Department.

^

Is it plugged in and switched on at
the socket?

Problem solving guide

63

Summary of Contents for CVA 5060

















































































Reviews: