Miele Allerdry T 4464 C Operating Instructions Manual Download Page 19

Page: 19 / 56

Timed drying

Max. load: 6 kg*

Warm air

Fabric type

–

Multi-layered fabrics whose layers have different drying
characteristics, e.g. jackets, pillows.

–

For drying individual items, e.g. bath towels, bathing
costumes, tea-towels.

Note

Do not select the longest drying time to start with. Check the
items as you are drying them to find the optimum time.

Additional
options

Low temperature (select this option for delicate fabrics with the

symbol on the care label), Buzzer.

Cool air

Fabric type

Any item which only needs airing.

Additional
option

Buzzer

Smoothing

Max. load: 3 kg*

Fabric type

–

Cottons and linen fabrics.

–

Minimum iron items made of mixed fibres, cottons or
synthetics, e.g. trousers, jackets, shirts.

Notes

–

Smooths out creasing caused during the spin cycle in the
washing machine.

–

Fabrics are not completely dried in this programme. Remove
garments as soon as the programme has finished and leave
to finish drying at room temperature.

Additional
options

Buzzer. Low temperature. (Low temperature cannot be
deselected).

Woollens hand care

Max. load: 2 kg*

Fabric type

Woollen fabrics

Notes

–

To refresh and fluff up woollen garments quickly. Woollen
fabrics are not dried completely by this programme.

–

Remove garments as soon as the programme has finished
and leave to finish drying at room temperature.

Additional
options

Buzzer. Low temperature. (Low temperature cannot be
deselected).

* Weight of dry laundry

Programme chart

Summary of Contents for Allerdry T 4464 C

























































Search results

Summary of Contents for Allerdry T 4464 C

Reviews:

Related manuals for Allerdry T 4464 C

Brands by name

Popular brands

Miele Allerdry T 4464 C, Operating Instructions Manual

Search results

Summary of Contents for Allerdry T 4464 C

Reviews:

Related manuals for Allerdry T 4464 C

Brands by name

Popular brands