Midtronics PowerSensor Micro500 Instruction Manual Download Page 16

PATENTS

Made in the U.S.A. by Midtronics, Inc. and is protected by one or more of the
following U.S. Patents: 6,469,511; 6,456,045; 6,445,158; 6,441,585; 6,392,414;
6,323,650; 6,316,914; 6,310,481; 6,304,087; 6,249,124; 6,225,808; 6,163,156;
6,091,245; 6,051,976; 5,831,435; 5,821,756; 5,757,192; 5,592,093; 5,585,728;
5,572,136; 4,912,416; 4,881,038; 4,825,170; 4,816,768; 4,322,685. Canadian
Patents: 1,295,680; 1,280,164. United Kingdom Patents: 0,672,248; 0,417,173.
German Patents: 693 25 388.6; 689 23 281.0-08; 93 21 638.6. European pat-
ents: C382.13-0040 WO; C382.13-0033 EP; C382.13-0018 EP. And other U.S.
and Foreign patents issued and pending. This product may utilize technology
exclusively licensed to Midtronics, Inc. by Johnson Controls, Inc. and /or Motorola,
Inc.

LIMITED WARRANTY

This battery analyzer is warranted to be free of defects in materials and
workmanship for a period of one year from date of purchase.  Midtronics will, at
our option, repair the unit or replace the unit with a remanufactured analyzer.
This limited warranty applies only to Midtronics battery analyzer and does not
cover any other equipment, static damage, water damage, overvoltage, dropping
the unit or damage resulting from extraneous causes including owner misuse.
Midtronics is not liable for any incidental or consequential damages for breach
of this warranty.  The warranty is void if owner attempts to disassemble the unit,
or to modify the cable assembly.

SERVICE

To obtain service, purchaser should contact Midtronics for a Return Authorization
number, and return the unit to Midtronics, attention:  Service Department. If
Midtronics determines that the failure was caused by misuse, alteration,
accident, or abnormal condition of operation or handling, you will be billed for the
repaired product and it will be returned to you freight prepaid.  Battery analyzers
beyond the warranty period are subject to the repair charges in effect at that
time.  Optional remanufacturing service is available to return the analyzer to like
new condition.

 

 15 

Summary of Contents for PowerSensor Micro500



















Reviews: