Midtronics GR1 240 Instruction Manual Download Page 10 | Manualshive

Page: 10 / 20

Midtronics GR1 240 Instruction Manual Download Page 10

10

Visually inspect the battery before charging. If there are any signs of a leaking or cracked case, discard the
battery.
Do not attempt to charge a battery that is in this condition.

FRONT PANEL

Under the display, there are 5 push buttons and an ON/OFF switch.

BACK PANEL

The back panel contains the positive and negative charging cables, the AC power cord, and a 9-pin connector.
The 9-pin connector is used to connect the serial printer to.

Note:

The 9-pin connector is also used for Service related items but only by authorized factory and service

technicians. Improper use of this connector will result in damage to the GR-1.

The handle, which attaches to the back panel, includes a clamp-holder bar. When used consistently, this feature
adds safety, convenience and longer operating life to the clamps, cables, and GR-1.

OPERATION

The

UP/DOWN

buttons are used for

scrolling through selections on the display
and to increase/decrease displayed values.

The

ENTER

button is used to accept

the displayed selection and to continue to
the next step.

The

INFO

button is used to enter the options menu,

which accesses the Languages, BMC Code,
Last Test Data and Print feature.

The

STOP

button is used to abort any

charging cycle. During menu selections, it
can be used to go back to the previous step.

«
...
8
9
10
11
12
...
»

Summary of Contents for GR1 240





















Reviews:

No comments