background image

 

3

ENGLISH

1 ABOVE ALL... SAFETY! 

1.1 Symbols used

For ease and convenience of viewing, NEPTUNE uses symbols to highlight urgent situations, 
practical advice, and general information.

 

Warnings such as this, shown using an open hand symbol, indicate a crucial description 
regarding technical repairs, dangerous conditions, safety warnings, advice and/or impor-
tant information.  Ignoring these symbols may result in serious problems and/or damage 
and/or personal injury.

  

Notes  such  as  this  one  indicate  practical  advice  that  we  suggest  be  followed  for  optimal 
performance with NEPTUNE.

1.2 Warnings

1.2.a General

  This  device  has  been  tested  for  compliance  with  Class  D  digital  marine  device  limits.  

These limits were created to allow for reasonable protection against damaging interfe-
rence.

  This device is to be used solely as an aid to navigation.  Its settings may be influenced by 

diverse factors, such as defects or malfunction of the device, environmental conditions 
or improper use.

  It is the user’s responsibility to observe reasonable prudence and judgement in naviga-

tion, and as such this device should not be considered a substitute for this reasonable 
prudence and judgement.

  Do not open the radio for any reason!  NEPTUNE’s precision mechanics and electronics 

require expertise and specialized equipment; for the same reason, the radio should under 
no circumstances be realigned as it has already been calibrated for maximum performan-
ce.  Unauthorized opening of the transceiver will nullify the warranty.

1.2.b Radiofrequency/installation

  Midland recommends following the requirements for prevention of radiofrequency expo-

sure.  Unauthorized changes or modifications to this device may invalidate conformity 
to  the  ETSI  Regulations.  All  changes  or  modifications  must  be  approved  in  writing  by 
MIDLAND Corp.

  This VHF DSC transceiver generates and irradiates electromagnetic energy (EME) at ra-

diofrequency (RF), and as such must be installed and placed in operating conditions that 
are in conformity with the instructions contained in this manual and with current regula-
tions.  Not following these instructions can cause personal injury and/or malfunction of 
the device.

  Do  not  use  NEPTUNE  before  connecting  a  suitable  antenna  that  is  in  perfect  working 

condition  –  although  NEPTUNE  is  protected,  this  may  seriously  damage  the  stages  of 
transmission power.

  Do not use transmit before ensuring proper connection of the antenna.  During transmis-

sion, remain at a minimum distance of 1mt from the antenna.

1.2.c Automatic Transmitter  Identification System (ATIS)

  Your marine transceiver may activate, if necessary, the ATIS function.  The ATIS function 

may be activated when using the transceiver within the internal navigable waters of Euro-
pe which require the automatic transmission of identification.  For further details, please 
contact your local authorities.

Summary of Contents for neptune

































Reviews: