Midland F-20 FRS Owner'S Manual Download Page 9

OWNER’S MANUAL FOR THE F-20 (FRS W/532 CODES) 

http://www.midlandradio.com 

9

 

DISPLAY SYMBOLS 

 

 

 

 
 

CAUTION: DON'T EXPOSE THE DISPLAY TO EXTREME HOT OR COLD TEMPERATURE 

 

1. Channel number:

 Displays channel number 1-14. 

2. BUSY Symbol: 

Indicates activity on the channel. 

3. TX Symbol: 

Indicates the unit is transmitting. 

4. CTCSS Code: 

Displays the number of the code selected for the channel in use. 

5.  SCAN Symbol  

Indicates the scan mode is in use 

6. CTCSS Symbol: 

Indicates a “Privacy” code is in use. 

7. SAVE Symbol: 

Flashes indicating battery save is active. 

8. Musical 

note

 indicates 

ROGER BEEP

 is on.   

9. Key Symbol

 indicates when the keypad has been locked. Only the 

“PTT”

 and 

“CALL”

 

buttons are active when this indicator is on. 

10. BEEP 

indicates the button press tone and power up tones are active. 

11. DW Symbol: 

Indicates Dual Watch channel selection is active. 

12. VOX Symbol: 

Indicates “VOX” is activated 

13. Battery symbol

 shows the battery condition. Replace or recharge the batteries when this 

indicator displays 2 or fewer segments of the battery. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for F-20 FRS













Reviews: