background image

16

OPERATION

 

SVR Operation: 

Repeater Enable/Disable:

  Press the radio key that was assigned during installation and/or radio programming. 

A medium tone followed by a high tone will sound indicating repeat mode is enabled.  When pressed again a 
medium tone followed by a low tone will sound indicating repeat mode is disabled. 

Repeat:

 With the SVR enabled, when the unit detects COR or VOX (depending on programming) it will record the 

incoming audio transmission. When COR or VOX drops for a preprogrammed amount of time, the unit will key the 
connected transceiver and retransmit the recorded audio. 

TECHNICAL NOTES

 

Radio Compatibility:

  Midian has taken the utmost care to ensure the option board integrates into the radio with 

minimal impact to the features of the radio.  However, some features may not be available in the radio when an 
option board is used.  If a feature is not available, please contact Midian to see if the feature can be added. 

MIDIAN CONTACT INFORMATION

 

MIDIAN ELECTRONICS, INC. 

2030 N. Forbes Blvd. #101

Tucson, Arizona 85745 USA

Toll-Free:

 1-800-MIDIANS 

Main:

 520-884-7981 

E-mail:

 

[email protected]

 

Web:

 

www.midians.com

Summary of Contents for SVR-1-IC1





















Reviews: