background image

 

9

CONTROLS & INDICATORS

 

 

 

 

Power/Volume Switch: 

On the right side of the TRC, there is a switch which acts as the power and volume 

switch. The switch is in the power off position when turned fully clockwise past the click. Turning the switch 
counter-clockwise past the click turns the power on to the volume control. At this point the volume is in the low 
position. Turning the switch further counter-clockwise increases the volume. 
 

LED 1 (PWR - LINE/SUP): 

This LED is a bi-color LED. The LED will glow red when the power is on to the TRC. It 

glows orange when Line 2/Supervisor mode is active. 
 

LED 2 (SEND - F1/F2): 

This LED is a tri-color LED. The LED will glow red during transmit of Freq 1 and orange 

during transmit of Freq 2. It glows green when Guard Tone is detected from a parallel tone remote. 
 

FREQ: 

The FREQ button acts as the frequency select key. Pressing this key once will give a single beep to 

indicate F1. Pressing this key again will give a double beep to indicate F2.  
 

INTER: 

Pressing the INTER key will allow intercom communications between several connected tone remotes 

without transmitting over the radio. When the INTER key is pressed and held, the audio is routed on the line 
without the Guard Tone activating the transmitter. Other tone remotes on the same line will hear the audio 
automatically. No cross mute is available in intercom mode since there is no Guard Tone present. 
 

MONITOR:

 Pressing the MONITOR key will allow the user to monitor the channel before pressing the SEND key 

to make a call. If a conversation is heard then another co-channel user presently “owns” the channel and should 
not be interrupted. 
 

SEND:

 Pressing SEND will transmit the high-level guard tone for 120 msec, followed by the frequency tone for 40 

msec, followed by the low-level guard tone that keys the radio with the voice and dialing riding over the low-level 
continuous tone. 
 

Optional 0-9, *, # Keys:

 These keys are used to dial DTMF. Press the desired buttons followed by the SEND key 

transmits the DTMF. 

 

 

 

ABC 

DEF 

GHI 

JKL 

MNO

PQRS 

TUV 

WXYZ

MENU 

OPER 

CLR

FREQ 

INTER 

 

MONITOR 

 

SEND 

  PWR - LINE/SUP           SEND - F1/F2 

Summary of Contents for TRC-2























Reviews: