Midian Electronics SVR-1-KW3 Manual Download Page 15

 

15

Kenwood NX-700 NX-800

:   

 

Note:

  The  radio  firmware  must  be  at  least  2.00.00.01  and  the  radio  programming  software  must  be  KPG-111D 

version 2.00 or higher. 
 
Under the “Edit” menu select “Extended Function” and set “Optional Board” as “Voice Scrambler”. OPT11 should 
be set as COR or TOR and Echo PTT should not be checked. To program the unit through the radio the Optional 
Board Programming must also be checked. 
 

 

 
When using a button to turn the repeater on and off program the desired button to “Scrambler/Encryption”. 
 

 

 
If repeating on a per channel basis is desired or a combination of button and per channel control, then click on the 
“Channel Edit” button on the “Zone Information” screen.  Under “Scrambler Setting” enable the “Voice Scrambler”.  
For repeat on a per channel basis, this will need to be done for each channel where repeat is desired.  If the box 
is checked, the radio will power up in repeat mode & when that channel is selected.  When per channel repeat is 
used, it is still possible to toggle in and out of repeat mode. 
 

 

 
 

 

Summary of Contents for SVR-1-KW3





















Reviews: