background image

 

28 

 

fan in cooling mode. 

Mute function is active. 

All protections are activated and operate the   

same as they do that in cooling mode. 

Low Room Temperature Protection 

-If the room temperature is lower than 10

, the 

compressor ceases operations and does not 

resume until room temperature exceeds 12

 

 

9.4.6 Forced Operation 

1. Forced cooling mode: 

The compressor and outdoor fan continue to run 

and the indoor fan runs at rated speed. After 

running for 30 minutes, the AC will switch to auto 

mode with a preset temperature of 24

2. Forced auto mode: 

Forced auto mode operates the same as normal 

auto mode with a preset temperature of 24

3. The unit exits forced operation when it receives 

the following signals: 

 

switch on   

 

switch off   

 

timer on   

 

timer off   

 

changes in: 

mode 

fan speed 

 

setting temperature. 

 

9.4.7 Timer function 

1. Timing range is 24 hours. 
2.Timer on. The machine will turn on 
automatically when reaching the setting time. 
3.Timer off. The machine will turn off 
automatically when reaching the setting time. 
4.Timer on/off. The machine will turn on 
automatically when reaching the setting “on” 

time, and then turn off automatically when 
reaching the setting “off” time. 
5.Timer off/on. The machine will turn off 
automatically when reaching the setting “off” 
time, and then turn on automatically when 
reaching the setting “on” time. 
6.The timer function will not change the AC 
current operation mode. Suppose AC is off now, 
it will not start up firstly after setting the “timer 
off” function. And when reaching the setting 
time, the timer LED will be off and the AC 
running mode has not been changed. 
7. The setting time is relative time. 
8. The AC will quit the timer function when it 
has malfunction. 
 

9.4.8 Sleep function 

1 The sleep function is available in cooling, 

heating, or auto mode. 

2. The operational process for sleep mode is as 

follows: 

 

When cooling, the temperature rises 1

 (to 

not higher than 30

) every hour. After 2 

hours, the temperature stops rising and the 

indoor fan is fixed to low speed.     

 

When heating, the temperature decreases 

1

  (to not lower than 16

) every hour. 

After 2 hours, the temperature stops 

decreasing and the indoor fan is fixed at 

low speed. Anti-cold wind function takes 

priority. 

3 The operating time for sleep mode is 8 hours, 

after which, the unit exits this mode and does 

not switch off. 

4 The timer setting is available in this mode. 

 

9.4.9 Auto-Restart function 

The indoor unit has an auto-restart module that 

allows the unit to restart automatically. The 

Summary of Contents for MSMTAU-09HRFN8-QRD6GW






















































Reviews: