P.20
P.21
Operate
Machine
Washer Dryer
Operate
Machine
Washer Dryer
- Reload
This operation can be executed during the washing procedure. When the drum of the
washing machine is still rolling and there is large amount of water with high temperature
in the drum. The state is unsafe and the door cannot be opened forcefully. To press
《
Start/Pause
》
for 3 sec. to reload, and start the clothes adding in the midway function .
Please follow the steps as bellow:
1.Wait until the drum stops rotation. 2.The door lock is unlocked.
3.Close the door when the clothes needs are loaded and repress the
《
Start/Pause
》
button.
Notes:
- Child Lock
To avoid that the washing procedure cannot operate normally due to the mis operation by
kids during the washing procedure, you can select this function, In this case, the other
buttons except On/Off button can not work, at this state ,the machine power off when press
the key on/off. The machine remembers the program child lock and the program during
powered off when press the key on/off again.
Press Function and Select together 3 seconds during the running procedure, the buzzer
will beep ,Start/Pause button as well as the rotary switch are locked. Press the two buttons
for 3 seconds together and buzzer will beep to release to locking. But cut off the power
supply , the kid’s protection is also release to locking. The kid’s protection will not be
cancelled after all procedures are completed.
-
Suppression of the acoustic signals
This is an additional buzzer function on your appliance. After deactivating the buzzer
function, the buzzer will be closed.
After starting the machine, press the “Temp. and Dry” button for 3 seconds and you will
hear a beep, then the buzzer will be closed. To restart the buzzer function, press the “Temp.
and Level” button again for 3 seconds. The setting will be kept until the next reset.
-
Bubble Removal Function
Bubble Check Function: Redundant bubbles will occur when there is excessive detergent,
which will affect wash and rinse effects. The procedure will check automatically and one
bubble removal procedure will be added automatically to remove bubbles when excessive
bubbles are checked.
- Sport Wear
You can select this procedure to wash the Sport Wear.
-
Quick
This procedure is suitable for washing few and not very dirty clothes quickly.
You can select this procedure to wash your delicate clothes. Its washing intension is
gentler and revolution speed is less compared with the procedure “Synthetic”. It is
recommended for the articles to be washed softly.
So dirty clothes can choose this function
.
It can select the prewash function to increase the
washing effect, you need to put detergent into the Case (I) when using pre-wash function.
- Delicate
- Wool
You can select this procedure to wash the wool textiles labeled with “Machine Wash”.
Please select the proper washing temperature according to the label on the articles to be
washed. Furthermore, the proper detergent shall be selected for wool textiles.
-
Spin Only
Separate spin only procedure. Soap water or rinse water shall be drained out before spinning.
-
Rinse&Spin
Separate Rinse&Spin Procedure.
- My Cycle
Press Temp. button 3sec. for my cycle to memory the procedure. The default my cycle is cotton.
The main function can be selected as follows:
-
Prewash
The Prewash function can get an extra wash before main wash.
- Extra Wash
-
Extra Rinse
The laundry will undergo extra rinse once after you select it.
-
Less Iron
Anti -crease function can be used to reduce the wrinkles of clothes.
- Delay
Delay function can be set with this button, the delaying time is 0-24 H.
Set the Delay function:
1. Select a programme;
2.Press the Delay button to choose the time;
3.Press Start/Pause to commence the delay operation
.
Cancel the Delay function: Press the Delay button until the display will be 0H.It should be
pressed before starting the program. If the program already started, should press the
On/Off button.
Notes: If there is any break in the power supply while the machine is operating, a special
memory stores the selected programme and when the power is restarted, press the
Start/Pause button the left time is continues
.
