manualshive.com logo in svg

Midea LSBLG1120/MCFN, Technical & Service Manual

Share
Download
Midea LSBLG1120/MCFN Technical & Service Manual Download Page 38

Flooded type water cooled screw chiller (PCB Control) 

 

MCAC-CTSM-2012-11 

38 

 

 

              

                                      Current Data Display 

Input 

Click on “

” to enter “Input Page” 

 

Input Status 

“ON” as displayed indicates the input point is closed; “OFF” as displayed indicates the input point is 

open. 

Note: 

①

  “Remote Start/Stop” is available only under REMOTE mode. According to inching output from use’s 

remote order, “Remote Start” or “Remote Stop” switch to ON and then revert to OFF rapidly. 

②

   “Chilled/Cooling Water Switch”: indicating that current water flow status of chilled water system. 

“OFF” displayed in no water flow state, otherwise “ON”.   

③

  “Contactor Protection”: indicating that when the compressor start to run, the contactor   act 

normally, “OFF” switch to “ON”. 

④

  All of protection switches are “ON” in normal except “Comp. Overload Prot. Switch”. “Comp. 

Overload Prot. Switch” is “ON” in failure status and “OFF” in normal. 

Output Status 

Click on “

” to enter “Output Page”,

 

Summary of Contents for LSBLG1120/MCFN


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands