background image

C. OPERATION

1.

TO PROGRAM A NEW

PRESET MENU SE-

LECTION:

Perform the procedure in Section E, 

Programming Preset Menu Selections

, on Page 5.  At least one

menu selection MUST be programmed before the oven can be operated.

Perform the procedure in Section E, 

Programming Preset Menu Selections

, BUT press 

 instead

of 

 (in Steps 3 and 8).  Instead of permanently overwriting the menu selection, the new set

temperature and cook time settings are only temporary.  To cancel the temporary menu selection,

press any preset menu key or disconnect electrical power to the oven.

2.

TO TEMPORARILY

OVERRIDE A PRE-

SET MENU SELEC-

TION:

a. Press 

 (or any other preset menu key).  The display will read 

 .  The number

in the display (“1” is shown above) will match the menu key that was pressed (1-5).

b. Wait for the 

 light to illuminate.  The light will illuminate after both heating zones reach

their set temperatures.

c. Load the product onto the conveyor.

3.

TO CHOOSE A PRE-

SET MENU SELEC-

TION:

a. Choose a preset menu selection, and wait for the 

 light to illuminate.

b. Press 

 .  

 and 

  will alternate in the display.  The number in the

display (“1” is shown above) will match the current menu selection (1-5).

c. Load the pizza product onto the conveyor.

IMPORTANT

After 1/2 of the cook time has elapsed, the temperature of the top zone will be automatically lowered.

After the entire cook time has elapsed, the program will return to its normal top zone temperature.

After 

 is pressed, the menu selection cannot be changed until the cook time has elapsed.

4.

TO COOK A SINGLE

PIZZA, OR THE LAST

OF A GROUP OF PIZ-

ZAS:

5.

TO VIEW THE SET

TEMPERATURES:

6.

TO VIEW HEATING

ZONE REFERENCE

TEMPERATURES:

Press either 

 or 

 .  The top or bottom set temperature will be displayed for 5 seconds.

D. SHUTDOWN PROCEDURE

1. Switch the Power On/Off (I/O) switch to the OFF (“O”) position.

2. Wait for the oven’s cooling fan to turn off.

3. Disconnect electrical power to the oven at the circuit breaker/fused disconnect.

7.

TO VIEW THE COOK

TIME:

Press 

 + 

 or 

 

 + 

 .  The top or bottom reference temperature will be displayed for

5 seconds.

Press 

 .  The cook time will be displayed for 5 seconds.

4

Summary of Contents for CTX Mighty Chef TCO2114













Reviews: