background image

2

ENGLISH

Middleby Cooking Systems Group • 1400 Toastmaster Drive • Elgin, IL 60120 • USA • (847)741-3300 • FAX (847)741-4406

24-Hour Service Hotline:  1-(800)-238-8444

www.middleby.com

Retain  This  Manual  For  Future  Reference

NOTICE:
This Owner's Operating and Installation Manual should be given to the user.  The operator of the oven should

be familiar with the functions and operation of the oven.
This manual must be kept in a prominent, easily reachable location near the oven.
Gas ovens are designed for use with EITHER natural gas OR liquid propane gas, as specified on the serial plate.

Where permitted by local and national codes, the oven can be converted from natural gas to propane operation,

or from propane to natural gas operation.  This conversion requires the installation of the appropriate Middleby

Marshall Gas Conversion Kit by an Authorized Service Agent.
It is suggested to obtain a service contract with a Middleby Marshall Authorized Service Agent.

WARNING

POST, IN A PROMINENT LOCATION, THE EMERGENCY TELEPHONE NUMBER OF YOUR LOCAL GAS

SUPPLIER AND INSTRUCTIONS TO BE FOLLOWED IN THE EVENT YOU SMELL GAS.

Instructions to be followed in the event the user smells gas shall be obtained by consulting the local gas

supplier. If the smell of gas is detected, immediately call the emergency phone number of your local Gas

Company. They will have personnel and provisions available to correct the problem.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors or liquids in the vicinity of

this or any other appliance.

WARNING:

Improper  installation,  adjustment,  alteration,  service  or  maintenance

can cause property damage, injury or death. Read the installation,

operating  and  maintenance  instructions  thoroughly  before  installing

or  servicing  this  equipment.

NOTICE:  

CONTACT YOUR MIDDLEBY MARSHALL AUTHORIZED SERVICE AGENT TO PERFORM MAINTENANCE

AND REPAIRS.  AN AUTHORIZED SERVICE AGENCY DIRECTORY IS SUPPLIED WITH YOUR OVEN.

NOTICE:  

Using any parts other than genuine Middleby Marshall factory manufactured parts relieves the manufacturer of

all warranty and liability.

NOTICE:  

Middleby Marshall (Manufacturer) reserves the right to change specifications at any time.

NOTICE:  

The equipment warranty is not valid unless the oven is installed, started and demonstrated under  the supervision

of a factory certified installer.

IMPORTANT

An electrical wiring diagram for the oven is located inside the machinery

compartment.

IMPORTANT

It is the customer's responsibility to report any concealed or non-concealed damage

to the freight company.  Retain all shipping materials until it is certain that the

equipment has not suffered concealed shipping damage.

Summary of Contents for PS570S























Reviews: