background image

2

E

N

G

L

IS

H

Middleby Cooking Systems Group • 1400 Toastmaster Drive • Elgin, IL 60120 • USA • (847)741-3300 • FAX (847)741-4406

Retain  This  Manual  For  Future  Reference

NOTICE:

This Owner's Operating and Installation Manual should be given to the user.  The operator of the oven should
be familiar with the functions and operation of the oven.

This manual must be kept in a prominent, easily reachable location near the oven.

Ovens are shipped from the factory configured for use with natural gas.  If permitted by local, national and
international  codes,  at  the  time  of  installation  the  oven  may  be  converted  to  propane  gas  operation.  This
conversion requires the use of at Gas Conversion Kit that is supplied with the oven. For CE-approved ovens, the
conversion is described in the 

Installation section of this Manual. For domestic and standard export ovens,

instructions are included in the Gas Conversion Kit.

It is suggested to obtain a service contract with a Middleby Marshall Authorized Service Agent.

WARNING

POST, IN A PROMINENT LOCATION, THE EMERGENCY TELEPHONE NUMBER OF YOUR LOCAL GAS

SUPPLIER AND INSTRUCTIONS TO BE FOLLOWED IN THE EVENT YOU SMELL GAS.

Instructions to be followed in the event the user smells gas shall be obtained by consulting the local gas

supplier. If the smell of gas is detected, immediately call the emergency phone number of your local Gas

Company. They will have personnel and provisions available to correct the problem.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors or liquids in the vicinity of

this or any other appliance.

WARNING:

Improper  installation,  adjustment,  alteration,  service  or  maintenance

can  cause  property  damage,  injury  or  death.  Read  the  installation,

operating  and  maintenance  instructions  thoroughly  before  installing

or  servicing  this  equipment.

NOTICE:

CONTACT YOUR MIDDLEBY MARSHALL AUTHORIZED SERVICE AGENT TO PERFORM MAINTENANCE

AND REPAIRS.  AN AUTHORIZED SERVICE AGENCY DIRECTORY IS SUPPLIED WITH YOUR OVEN.

NOTICE:

Using any parts other than genuine Middleby Marshall factory manufactured parts relieves the manufacturer of

all warranty and liability.

NOTICE:  

Middleby Marshall (Manufacturer) reserves the right to change specifications at any time.

NOTICE:

The equipment warranty is not valid unless the oven is installed, started and demonstrated under  the supervision

of a factory certified installer.

IMPORTANT

An electrical wiring diagram for the oven is located inside the machinery

compartment.

IMPORTANT

It is the customer's responsibility to report any concealed or non-concealed damage

to the freight company.  Retain all shipping materials until it is certain that the

equipment has not suffered concealed shipping damage.

www.middleby.com

24-Hour Service Hotline:  1-(800)-238-8444  •  Middleby Customer Care Center:  1-(800)-630-6559

Summary of Contents for PS536GS













































Reviews: