background image

©2017 Mid West Products, Inc. 

-3- 

Form No. M1-1603 

C)  Place  Tie  Rod  (82)  through  lip  on  front  of 

Hamper and put a Flat Washer (30) on each end.  
Place  two  Front  Lower  Hamper  Tubes  (84) 
inside  Hamper  and  onto  ends  of  the  Rod.  
Secure with two Lock Nuts (9) on each end.  With 
flat  end  of  Front  Hamper  Tubes  (84)  on  the 
outside of Tube (83), align holes and fasten with 
two  Bolts  (41)  and  two  Lock  Nuts  (9).    Do  not 
tighten at this time. 

 
D)  Take Lower Rear Tube (86) and place it over the 

ends  of  Tubes  (84)  and  align  holes.    Then 
position the Rear Corner Tubes (90) over holes 
and  insert  a  Tube  Bolt  (85)  through  each  side 
and secure with two Lock Nuts (9). 

 

E)  Pulling back of Hamper up with Tube (91), align 

holes in Corner Tubes (90) and insert two Bolts 
(41) and secure with two Lock Nuts (9).  At this 
time securely tighten all Bolts in this assembly. 

 

F) 

Pulling up and back on Wind Apron (80), align its 
velcro  tabs  to  tabs  on  side  panels  of  Hamper 
(87).

 

 

Place Hamper Assembly from Figure 1 onto Hamper 
Support Assembly from Figure 2. 
 

A) 

With  Sleeves  (65)  in  holes  in  Hamper  Support 
Tube  (66),  place  Hamper  Assembly  in  position 
with  Pivot  Brackets  (89),  straddle  ends  of  
Support  Tube  (66).    Align  hoIes  and  insert  two 
Bolts (88) and secure with two Lock Nuts (67).

 

 

B)  Securely tie Dump Rope (15) to center of Rear 

Upper  Tube  (91).    Run  Rope  under  Hamper, 
then  up  between  Hamper  and  Tube  (66)  and 
through  Grommet  in  top  of  Lawn  sweeper.  
Locate Dump Handle (16) on Rope where it can 
be reached from your Tractor seat and secure by 
tying a knot on both sides of it. 

 
Attach Hitch Brackets to Lawn sweeper Tongue as 
follows and as shown in Figure 3. 
 
A)  Due  to  the  wide  range  of  Tractor  sizes  and 

drawbar heights, mounting of the Hitch Brackets 
may vary, depending on your particular Tractor.  
Top  of  Lawn  Sweeper  Tongue  (45)  should  be 
level or approximately 

8” off the ground with the 

Lawn Sweeper in the Iowest setting. 

 

B) 

See  Figure  3  and  select  the  recommended 
mounting  to  suit  your  particular  Tractor  hitch 
height.  Then attach Hitch Brackets (43 and 44) 
with  two  Bolts  (42)  and  secure  with  two  Lock 
Nuts (9).

 

 

 

Figure 2

 

Figure 3

 

Summary of Contents for HDT-38B










Reviews: