manualshive.com logo in svg

Micsig ATOIOOO Series, User Manual

The Micsig ATOIOOO Series is a cutting-edge test and measurement equipment, designed to meet all your technical needs. With a comprehensive User Manual available for free download on our website, you can easily navigate through all the features and functionalities of this exceptional product. Get the most out of the Micsig ATOIOOO Series by downloading the manual from manualshive.com.

Share
Download
background image

 

 

 

268 

2)

 

In the main menu, tap "Save" to enter the save menu. 

3)

 

In the Save menu, tap "Save" to open the Save Reference Waveform menu and make the following settings: 

 

Storage location: locally. 

 

Selecting the file type: WAV. 

 

Entering the file name: CH1. 

4)

 

Tap “Save” to save the reference file. The save success prompt box is popped up. 

 

If the reference waveform file is to be saved in USB device, the oscilloscope must be connected to an external 

USB device. After connection, the reference waveform save location is preferentially set to the USB device. 

 

There is no limit to the number of saved reference waveform files. 

Method 2: Click R* button   

In the Save Reference Waveform menu, tap R* (R1, R2, R3, R4) button to save the current channel waveform 

directly to the corresponding reference channel, and the save success prompt will pop up. The file name is displayed 

Summary of Contents for ATOIOOO Series












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ATOIOOO Series

Radarcan R-106 User Manual preview
R-106
Brand: Radarcan Pages: 40
iHealth PO3M Quick Start Manual preview
PO3M
Brand: iHealth Pages: 8
Taylor 358 Service Manual preview
358
Brand: Taylor Pages: 60
TANDBERG Model 5 Service Manual preview
Model 5
Brand: TANDBERG Pages: 23
Backyard Play Systems 4431 Assembly Instructions Manual preview
4431
Brand: Backyard Play Systems Pages: 73
natus ALGO 5 Installation And Assembly Instructions preview
ALGO 5
Brand: natus Pages: 20
natus Dantec Keypoint G4 Hardware Instructions For Use preview
Dantec Keypoint G4
Brand: natus Pages: 42
natus Madsen Zodiac Reference Manual preview
Madsen Zodiac
Brand: natus Pages: 149
Hoist Fitness HPA-2 Owner'S Manual preview
HPA-2
Brand: Hoist Fitness Pages: 17
Peak Pilates Wunda Assembly Manual preview
Wunda
Brand: Peak Pilates Pages: 4
Toro 02720 Operator'S Manual preview
02720
Brand: Toro Pages: 12
HYDRA-RIB 21166904 Owner'S Manual preview
21166904
Brand: HYDRA-RIB Pages: 25
Osprey Medical R-PRL Instructions For Use Manual preview
R-PRL
Brand: Osprey Medical Pages: 49
Enerpac SGM Series Instruction Sheet preview
SGM Series
Brand: Enerpac Pages: 12
Master MS Seeds Instructions For Use And Maintenance Manual preview
MS Seeds
Brand: Master Pages: 24
Vollrath Signature Server 36112 Operator'S Manual preview
Signature Server 36112
Brand: Vollrath Pages: 12
Jäger Z62-M450.01 S21 Manual preview
Z62-M450.01 S21
Brand: Jäger Pages: 36
Denon DN-700R Owner'S Manual preview
DN-700R
Brand: Denon Pages: 119

Brands by name

Popular brands

Load more brands