5
6
To comply with FCC RF exposure requirements, the antenna used
for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or
transmitter.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
in encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experience radio/TV technician
for help.
This device complies with Canadian ICES-003, RSS-Gen, RSS-210
and RSS-310 of Industry Canada (IC). Operation is subject to the
following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
To comply with IC RF exposure compliance requirements, the
antenna used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna
or transmitter.
laser specifications
Caution
Use of controls or adjustments, or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
This device complies with International Standard IEC
60825-1:1993+A1+A2 (IEC 60825- 1:2001-08) for a Class 1 laser
product. This device also complies with 21 CFR 1040.10 and
1040.11 except for deviations pursuant to Laser Notice No. 50,
dated June 24, 2007.
The following Class 1 laser label is located on the foot of the sensor.
Disposal of Waste batteries and electrical & electronic
equipment
This symbol on the product or its batteries or its
packaging means that this product and any batteries it
contains must not be disposed of with your household
waste. Instead, it is your responsibility to hand this over to
an applicable collection point for the recycling of
batteries and electrical and electronic equipment. This separate
collection and recycling will help to conserve natural resources and
prevent potential negative consequences for human health and the
environment due to the possible presence of hazardous substances
in batteries and electrical and electronic equipment, which could
be caused by inappropriate disposal. For more information about
where to drop off your batteries and electrical and electronic waste,
please contact your local city/municipality office, your household
waste disposal service, or the shop where you purchased this
product. Contact [email protected] for additional information
about WEEE.
paTenT InForMaTIon
United States and/or international patents pending.
CopYrIGHT
Information in this document, including URL and other Internet
Web site references, is subject to change without notice. Unless
otherwise noted, the example companies, organisations, products,
domain names, e-mail addresses, logos, people, places and events
depicted herein are fictitious, and no association with any real
company, organisation, product, domain name, e-mail address,
logo, person, place or event is intended or should be inferred.
Complying with all applicable copyright laws is the responsibility
of the user. Without limiting the rights under copyright, no part of
this document may be reproduced, stored in or introduced into
a retrieval system, or transmitted in any form or by any means
(electronic, mechanical, photocopying, recording, or otherwise),
or for any purpose, without the express written permission of
Microsoft Corporation.
Microsoft may have patents, patent applications, trademarks,
copyrights, or other intellectual property rights covering subject
matter in this document. Except as expressly provided in any
written license agreement from Microsoft, the furnishing of
this document does not give you any license to these patents,
trademarks, copyrights, or other intellectual property.
© 2013 Microsoft Corporation. All rights reserved. Microsoft,
Windows, Xbox, Xbox 360, Kinect and the Xbox logos are
trademarks of the Microsoft group of companies.
This item incorporates copy protection technology that is
protected by U.S. patents and other intellectual property rights
of Rovi Corporation. Reverse engineering and disassembly are
prohibited.
Manufactured under license from Dolby Laboratories. “Dolby”
and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. Copyright 1999–2013 Dolby
Laboratories. All rights reserved.
HDMI, the HDMI logo, and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing, LLC.
The names of actual companies and products mentioned herein
may be the trademarks of their respective owners.
CUsToMer sUpporT
For answers to common questions, troubleshooting steps, and
Xbox Customer Support contact information, visit
www.xbox.com/support.
X188017902MNL.indd 6
3/13/13 12:02 PM
