manualshive.com logo in svg

Microsoft Surface Hub 55 inch, Assembly And Mounting Manual, Page: 8 / 14

Share
Download
Microsoft Surface Hub 55 inch Assembly And Mounting Manual Download Page 8

©2015 Microsoft. Microsoft, the Microsoft logo, and the Microsoft Surface Hub logo are trademarks of the Microsoft 
group of companies.  Microsoft Corporation One Microsoft Way Redmond, WA  98052-6399 USA  

 

Note

: Do not overtighten the nuts.

 

B.

 

Attach the display mount to the column. 

a.

 

Fit the center hole at the top of the display mount over the alignment pin at the 
top of the column.  

b.

 

Make sure the screw holes on the display mount align with the screw holes on 
the column. Insert the column screws into the holes and loosely tighten them 
with a hex key. 

c.

 

Once you’ve put in all the screws, tighten them fully. Do not overtighten.  

 

 

 

Step 2: Attach the mounting pucks and hang the Surface Hub on the rolling stand

 

A.

 

On the back of the Surface Hub, identify the mounting screw holes. 

B.

 

Use the 25mm puck screws to attach the mounting pucks to the back of the Surface Hub. 

C.

 

Tighten the screws fully. Do not overtighten. 

 

Summary of Contents for Surface Hub 55 inch















Reviews:

No comments