P
P
o
o
w
w
e
e
r
r
D
D
s
s
i
i
n
n
e
e
3
3
5
5
0
0
1
1
G
G
-
-
E
E
T
T
U
U
s
s
e
e
r
r
G
G
u
u
i
i
d
d
e
e
1
1
-
-
P
P
o
o
r
r
t
t
8
8
0
0
2
2
.
.
3
3
a
a
f
f
G
G
i
i
g
g
a
a
b
b
i
i
t
t
P
P
o
o
E
E
M
M
i
i
d
d
s
s
p
p
a
a
n
n
Notice
It is Microsemi’s policy to improve its products as new
technology, components, software, and firmware become
available. Microsemi, therefore, reserves the right to change
specifications without prior notice.
Technical Support
If you encounter problems when installing or using this
product, consult Microsemi website at:
U
http://www.Microsemi.com/powerdsine/support
U
/.
2011 Microsemi Corp.
Recycling and Disposal
Disposal instructions for old products. The WEEE
(Waste Electrical and Electronic Equipment)
national environmental initiatives has been put
in place to ensure that products are recycled
using best available treatment, and recovery
and recycling techniques to ensure human
health and high environmental protection. Your
product is designed and manufactured with
high quality materials and components which
can be recycled and reused. Do not dispose of
your old product in your general household
waste bin. Inform yourself about the local
separate collection system for electrical and
electronic products marked by this symbol:
Use one of the following disposal options :
1. Dispose of the complete product (including
its cables, plugs and accessories) in the
designated WEEE collection facilities.
2. If you purchase a replacement product,
return your older product (including all
components) back to the retailer. The retailer
should accept it as required by the national
WEEE legislation.
Ordering information:
•
Product Name:
PowerDsine 3501G-ET
•
Part Number:
PD-3501G-ET/AC
•
Description:
1-Port 802.3af Gigabit PoE Midspan
Extended temperature.
Document P/N: PD-3501G-ET-AC_UG Rev. 1.0
1B
Safety Information
8B
Important Safety Information
♦
PD-3501G-ET should be connected to PoE networks
only, without routing to outside plant.
♦
Only qualified personnel can install or remove PD-
3501G-ET.
♦
AC Power Cord Set:
Power cord must have regulatory agency approval for the
specific country in which it is used (for example UL, CSA,
VDE, etc.).
Power cord must be a three-conductor type (two current
carrying conductors; one ground conductor) terminated on
one end by an IEC 60320 appliance coupler (for
connection to PD-3501G-ET), and on the other end by a
plug containing a ground (earthing) contact.
Power cord must be rated for a minimum of 250 VAC RMS
operation, with a minimum rated current capacity of
5 amps, or a minimum wire gauge of 18 AWG (0.75 mm
2
).
: A PD-3501G-ET installed in Australia requires power cords
with a minimum wire gauge of 16 AWG (1.0 mm
2
).
: PD-3501G-ET "DATA IN" and "DATA&POWER OUT"
ports are shielded RJ45 data sockets. They
cannot
be used as
Plain Old Telephone Service (POTS) sockets. Only RJ45 data
connectors can be connected to these sockets.
♦
The AC wall socket-outlet must be near the PD-3501G-
ETand easily accessible. You can remove AC power
from the PD-3501G-ET by disconnecting the AC power
cord from either the wall socket-outlet or the PD-3501G-
ETappliance coupler.
♦
PD-3501G-ET DATA IN and DATA & POWER OUT
interfaces are qualified as Safety Extra-Low Voltage
(SELV) circuits according to IEC 60950-1. These
interfaces can only be connected to SELV interfaces on
other equipment.
2B
WARNINGS!
♦
PD-3501G-ET should only be connected to IP device
with which it was bought. Using PD-3501G-ET with
other IP devices can cause damage to IP device.
♦
Read installation instructions before connecting
PD-3501G-ET to its power source.
♦
Follow basic electricity safety measures whenever
connecting PD-3501G-ET to its power source.
♦
A voltage mismatch can cause equipment damage and
may pose a fire hazard. If voltage indicated on the label
is different from the power outlet voltage, do not connect
PD-3501G-ET to this power outlet.
♦
Unit can be used only in Restricted Access Locations.
