MicronWings Balsa Craft Cub Build Instructions Download | Manualshive

Page: 1 / 16

background image

Cub

(Build Instructions)

Before You Start

This airframe has been designed to fit together easily with all components precision drilled and
CNC cut from high quality balsa and paulownia wood. However, you will be working with very
small components, so you will need patience and keen eyesight. We recommend working in a very
well-lit area and taking a break between stages to rest the eyes and hands. Most of all, take your
time, enjoy the building experience and you will be proud of what you have produced in the end.

Specifications

Wingspan: 37.5cm

Length: 27.5cm

Flying Weight: 25 -28grams

Channels: 3 (Rudder Elevator Throttle)

Suggested Receiver: 3 - 4Ch Micro

Airframe Kit

(Included Contents)

* Airframe Surface Parts (balsa)

* Airframe Skeleton (hardwood)

* Carbon pushrods

* Control linkages / heat shrink

* Undercarriage with Wheels

* Fine sand paper

* Decal Stickers

* Geardrive with 7mm Motor

* Propeller

Needed to Complete

* Thick CA Glue or UHU Hart Glue

* Slow-Drying White Model Glue

* Micro Phillips Head Screwdriver

* Hobby Knife

* Ruler

* Pins

* Fine Point Tweezers

* Hobby Masking or Other Tape

* Receiver Transmitter Charger Battery

(see instructions for suggested RC gear setup)

1
2
3
...
»

Summary of Contents for Balsa Craft Cub

















Reviews:

No comments

Related manuals for Balsa Craft Cub

Brand: Hacker Pages: 8

Go Go Smart Wheels Ambulance

Brand: VTech Pages: 2

Floater Altitude 2,4 GHz

Brand: Jamara Pages: 12

Brand: Faller Pages: 16

Brand: Jamara Pages: 16

NUMBER FLASH CARDS 77824

Brand: Fisher-Price Pages: 12

Brand: skyangel Pages: 16

MAN F2000 Evolution

Brand: ROBBE Pages: 44

KOKUYO Flair Klixi Mixi

Brand: PREZIOSI Pages: 6

Brand: Eduard Pages: 6

imaginext J2532

Brand: Fisher-Price Pages: 12

TRACKMASTER T0787

Brand: Fisher-Price Pages: 1

Brand: Oregon Scientific Pages: 32

Brand: Smoby Pages: 7

Brand: Trix Pages: 48

Brand: Tamiya Pages: 6

EI-2309 Language Tutor

Brand: Educational Insights Pages: 8

Brand: LEXIBOOK Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands