General
Communication
USB device, USB host, LAN(1000BASE-T)
Interface
Full speed(12Mbps) @ USB 1.1
Transfer rate
Display
5.7 inches and color LCD
Display
LED backlight
Backlight
640(H) x 480(V) dots
Number of dots
Power supply
100 to 240VAC, 50 to 60Hz
Supply voltage
approx. 18W
approx. 20W
@ without option
@ with IQ modulator MIQ700 and
High stability timebase MSG700-03
Power consumption
Save
Saves each 10 lists for sweep and
FSK/PSK/IQ modulations, and 200 setting
parameters.
Load
Loads 1 list of sweep or FSK/PSK/IQ
modulation, and 1 setting parameter.
Save/Load
List sweep data, FSK/PSK modulation
signal data, list data for IQ modulator and
setting parameters can be saved.
USB flash drive
Synchronous output
High at signal output state and low at
carrier off state.
Other specifications are the same as
SWEEP section.
DC to 5MHz
1 to 10Vp-p
0.56V(fixed)
DC coupling
approx.36kΩ
±50V(DC+ACpeak)
External trigger
Frequency range
Input voltage range
Trigger level
Input coupling
Input resistance
Maximum input voltage
Connector
BNC(J)
Waveform display
Display waveform
Frequency/level vs. time
approx.2Vp-p @ no load, 0V at low level
Amplitude
approx.200Ω
Output impedance
DC coupling
Output coupling
9Vrms(including DC component)
Reverse voltage protection
BNC(J)
Connector
Synchronous output
Positive pulse is output during swept.
When the sweep is continuous, negative
pulse of more than 50μs width is output at
end of sweep.
Valid only in ALC off.
Modulation
Modulation signal source
Internal
Register mode, Direct mode
FSK/PSK data mode
Register mode
The shift amount of frequency or phase
written previously in eight registers (register
0 to 7) are read out by the internal modula
-
tion signal. Internal modulation signal is
stored in the modulation signal memory
(storing register number), and is read out at
the specified rate. Allows high-speed trans
-
mission.
Kinds of modulation
FSK modulation, PSK modulation, Ampli
-
tude modulation(AM)
Direct mode
The shift amount of frequency or phase
stored in modulation signal memory is
sequentially read out at specified rate.
Transmission rate
100Hz to 1MHz/point @ register mode
100Hz to 20kHz/point @ direct mode
100Hz/point
Setting resolution
Internal modulation signal source The modulation signal is stored in modula
-
tion signal memory. At register mode, the
register numbers are stored, and at direct
mode, the frequency values or phase
values are stored.
Save/Load
Save :
Load :
each 10 lists of FSK and PSK.
each 1 list of register mode and
direct mode (each of FSK and PSK).
Length of modulation
signal memory
2,048
An arbitrary memory length of 1 to 2,048
can be set.
*
Kinds of
modulation signal
PN9, PN15, List
PN9 and PN15 can be set only in binary
for both frequency and phase.
*
Burst control
Valid only in FSK and PSK
Control mode
Free run, External, Manual
Free run Continuous output
Manual
External
TRIG IN connector
High level : signal output
Low level : carrier off
Sets the signal output/carrier
off with TRIG key.
Single, Repeat
Operation mode
Single :
Control signal
Repeat :
Control signal
Output signal
Synchronous
output
Output signal
Synchronous
output
Top address of memory
Top
Final
Top
Final address
of memory
Carrier off level
Carrier off
level
FSK modulation
±500kHz
Frequency shift
1Hz
Resolution
Carrier frequency
Frequency vs. time
Waveform display
Sets the center of shift with FREQ key.
PSK modulation
±
180
deg
Phase shift
0.1
degree
Resolution
Phase vs. time
Waveform display
Carrier frequency
Sets with FREQ key.
Sine wave
Waveform
Modulation waveform
Waveform display
0 to 99%, 1% step
Modulation depth
100Hz to 5kHz, 100Hz step
Frequency
Carrier frequency
Amplitude modulation
Burst control mode can be used only in free
run.
Sets with FREQ key.
*
Can be used simultaneously with the modulation function.
*
Can be used simultaneously with the sweep function.
