background image

    

2.

2.

2.

2.6

66

6 Test Program

 Test Program

 Test Program

 Test Program

    

       
This test program verifies configuration of the adapter and assists 
the isolation of any faults in operation. Test procedure are 
optional, and will only be useful in the unusual event that there is 
a fault, such as an interrupt number conflict among your 
computer’s add on cards, If your installation provides normal 
operation, you do not need these test procedures.   
 
At your DOS prompt, type the following command: 

a:\setup.exe

 <Enter> 

The opening screen is displayed as following: 

 

View Current Configuration 
Set Up New Configuration 
Run Diagnostics 
Exit NETSETUP 

 

Choose <Set Up New Configuration> item allows you to set up 
the Network Speed, 10 or 100M, and Transmission Mode, Full or 
Half Duplex, and so on. Choose <Run Diagnostics> item to run 
the adapter test program.   
Adapter test program includes:   
<EEPROM Test>,   
<Run Diagnostics on Board>,   
<Run Diagnostics on Network>, and 
<Run Power Management Test>.   
The Power Management Test is available for WOL adapter only. 
 
After choosing the <Run Diagnostics on Board> item, the screen 
will display like, 

 

 

 

 

Node ID.....…….: 00 e0 7d c0 00 01 
Network Speed...: 100Mbps 
I/O Base .………: E000H 
Interrupt ..……...: 11 
Full-Duplex …...: Disabled 
 
                                            Pass Count    Fail Count 
A. I/O Register 
B. 100Mbps Loopback 
C. 10Mbps Loopback 
D. Cable Connection 

 
 

P/N: 50075-0000

Summary of Contents for EtherFast 100Mbps Fiber-Optic Adapter SP2515 SERIES











Reviews: