Microh Ultra Spot 700 User Manual Download Page 7

-

-

-

-

-

-

-

-

-

-

-

-

W hen rigging, derigging or servicing the fixture staying in the area below the installation place, on

bridges, under high working places and other endangered areas is forbidden.

The operator has to make sure that safety-relating and machine-technical installations are

approved by an expert before taking into operation for the first time and after changes before taking
into operation another time.

The operator has to make sure that safety-relating and machine-technical installations are

approved by an expert after every four year in the course of an acceptance test.

The operator has to make sure that safety-relating and machine-technical installations are

approved by a skilled person once a year.

The projector should be installed outside areas where persons m ay walk by or be seated.

Impor tank! Overhead rigging requires extensive experingCE, including (but not limited to)

calculating working load limits, installation material being used, and periodic safety inspection of all
installation material and the projector. If you lack these qualifications, do not attempt the installation
yourself, but instead use a professional structural rigger. Improper installation can result in bodily
injury and or damage to property.

The projector has to be installed out of the reach of people.

If the projector shall be lowered from the ceiling or high joists, professional trussing system s have

to be used. The projector must never be fixed swinging freely in the room .

Caution Projectors may cause severe injuries when crashing down! If you have doubts

concerning the safety of a possible installation, do NOT install the projector!

Before rigging make sure that the installation area can hold a minim um point load of 10 times the

projector s weight.

The projector can be placed directly on the stage floor or rigged in any orientation on atruss without

altering its operation characteristics.

For overhead use, always install a safety-rope that can hold at least 10 times the weight of the

fixture. You must only use safety-ropes with screw on carabines. Pull the safety-rope through the two
apertures on the bottom of the base and over the trussing system etc.

Mounting plate

Secure chain

Omega holder

5

Summary of Contents for Ultra Spot 700





















Reviews: