Microgate SyncLink USB Hardware User Manual Download Page 3

Overview

 

The SyncLink PCIe Serial Adapter is an add-in card for systems with PCI Express expansion slots. The card 
provides two serial ports for use by the system. A variety of serial protocols and interface standards are 
supported. Refer to the software documentation included with the card for details on using the card for 
specific applications. 

For compatibility the SyncLink PCIe identifies as a SyncLink GT2 when used with older drivers. The latest 
drivers identify the card as SyncLink PCIe and enable new features. 

Features 

 

Maximum Speed 10Mbps 

 

SDLC, HDLC, BISYNC, MONOSYNC, ASYNC, raw bit-synchronous, TDM/McASP protocols 

 

Selectable hardware CRC: CRC-16, CRC-32, None 

 

DPLL Clock Recovery (x8 and x16 sampling) 

 

Clock Generation 

 

Configurable transmit preamble and idle patterns 

 

Encoding: NRZ,NRZB,NRZ-L,NRZI,NRZ-M,NRZ-S,FM0,FM1,Manchester,differential biphase level 

 

Software and switch selectable interface for RS-232, V.35, RS-422/485, RS-530, RS-449, X.21 

 

Optional termination for differential inputs 

 

Full set of control and status signals (DTR,DSR,RTS,CTS,DCD,RI,LL,RL) 

 

Specifications 

 

MicroGate FPGA serial controller (2 ports) 

 

PCI Express (x1) 

 

Bus Master DMA data transfer 

 

Operating Temperature Range: -40C to +85C 

 

Storage Temperature Range: -55C to +125C 

 

Environmental: humidity 0 to 95% non-condensing;  alt. - 200 to +20,000 ft 

 

Mechanical: Standard PCI Express short card; length 3.8", height 4.0" 

 

Power usage:  2.5W (max) 

 

Regulatory: FCC, CE, RoHS 

 

Connectors: HD-26 male (x2) with adapter cable included to convert to DB-25 male. 

 

Cable Options: DB-25 (female) to DB-25 (male); DB-25 (female) to 34-pin V.35 (male); DB-25 
(female) to 37-pin RS-449 (male); DB-25 (female) to 15-pin X.21 (male) 

 

PCI Express

 

PCI Express is an expansion slot standard for adding components to a system. PCI Express is not 
compatible with PCI or PCI-X slots. SyncLink cards are keyed to prevent insertion into incompatible slots. 
The SyncLink PCIe is a x1 (single lane) card and is compatible with any of the different PCI Express slots 
sizes (x1, x4, x8, or x16). PCI Express x1 slots are the shortest and x16 slots are the longest. 

Summary of Contents for SyncLink USB














Reviews: