Microgate SyncLink GT2E Hardware User Manual Download Page 3

Overview

 

The SyncLink GT2E and GT4E Serial Adapters are add-in cards for use in systems with a PCI Express 
expansion slot. The cards provide two (GT2E) or four (GT4E) serial ports for use by the system. A variety 
of serial protocols and interface standards are supported. Refer to the software documentation included 
with the card for details on using the card for a specific application. 

Features 

 

Maximum Speeds 
10Mbps synchronous 
8Mbps asynchronous 

 

SDLC, HDLC, BISYNC, MONOSYNC, ASYNC, raw bit-synchronous protocols 

 

Selectable hardware CRC: CRC-16, CRC-32, None 

 

DPLL Clock Recovery (x8 and x16 sampling) 

 

Clock Generation 

 

Configurable transmit preamble and idle patterns 

 

Encoding: NRZ,NRZB,NRZ-L,NRZI,NRZ-M,NRZ-S,FM0,FM1,Manchester,differential biphase level 

 

Selectable interface for RS-232, V.35, RS-422/485, RS-530, RS-449, X.21 

 

Optional termination for differential inputs 

 

Full set of control and status signals (DTR,DSR,RTS,CTS,DCD,RI,LL,RL) 

 

Specifications 

 

MicroGate FPGA serial controller (2 or 4 ports) 

 

PCI Express (x1) 

 

Bus Master DMA data transfer 

 

Operating Temperature Range: 0C to 70C standard, -40C to +85C optional 

 

Storage Temperature Range: -55C to +125C 

 

Environmental: humidity 0 to 95% non-condensing;  alt. - 200 to +20,000 ft 

 

Mechanical: Standard PCI Express short card; length 6.6", height 4.2",  Weight 4.4 Oz 

 

Power usage:  1A 3.3V 

 

Regulatory: FCC Class B, CE, ANSI C63.4 Class B, VCCI Class B, EN55022 Class B, EN55024, RoHS 

 

Connectors: DB-25 (male) 

 

Cable Options: DB-25 (female) to DB-25 (male); DB-25 (female) to 34-pin V.35 (male); DB-25 
(female) to 37-pin RS-449 (male); DB-25 (female) to 15-pin X.21 (male) 

 

PCI Express

 

PCI Express is an expansion slot standard for adding components to a system. PCI Express is not 
physically compatible with PCI or PCI-X slots. SyncLink cards are physically keyed to prevent insertion 
into incompatible slots. The SyncLink GT2E and GT4E are PCI Express x1 single lane cards. This means 
SyncLink cards work in any of the different PCI Express slots sizes (x1, x4, x8, or x16). PCI Express x1 slots 
are the shortest and x16 slots are the longest. 

Summary of Contents for SyncLink GT2E



















Reviews: