Microgate SyncLink GT2E Hardware User Manual Download Page 13

RS-422/RS-449/RS-485/RS-530 

The RS-422 and RS-485 standards describe differential electrical signals but not connector or pin 
assignments. The RS-530 and RS-449 standards define specific connectors and pin assignments using 
differential signals. The differential signals on the card meet both RS-422 and RS-485 electrical 
specifications. 

RS-530 uses differential signals on a DB-25 connector. The adapter DB-25 connector follows this 
standard when the port jumpers are installed for RS-422/485. Use any straight through 25 conductor 
DB-25M to DB-25F cable (such as MicroGate Part # CMF000) to connect the adapter to RS-530 
communications equipment. 

RS-449 uses differential signals on a DB-37 connector. To use this standard install the RS-422/485 
jumpers for the port and use the MicroGate RS-449 cable (Part # 2537FM). 

The maximum data rate supported by the adapter when using RS-530 or RS-449 is 10Mbps. Cable length 
and signal loading may reduce the maximum usable data rate from this value. 

RS-422/RS-530/RS-449 Male DTE 

Signal Name 

Electrical Desc 

DB25 

RS-530 

Pin # 

DB37 

RS-449 

Pin # 

Direction 

Earth/Shield Ground 

 

 

TxD (-/A), Transmit Data 

RS-422/V.11 

Output 

RxD (-/A), Receive Data 

RS-422/V.11 

Input 

RTS (-/A), Request to Send 

RS-422/V.11 

Output 

CTS (-/A), Clear to Send 

RS-422/V.11 

Input 

DSR (-/A), Data Set Ready 

RS-422/V.11 

11 

Input 

Signal Ground 

 

19 

 

DCD (-/A), Data Carrier Detect 

RS-422/V.11 

13 

Input 

RxC (+/B), Receive Clock 

RS-422/V.11 

26 

Input 

DCD (+/B), Data Carrier Detect 

RS-422/V.11 

10 

31 

Input 

AuxClk (+/B), DTE Clock Output 

RS-422/V.11 

11 

35 

Output 

TxC (+/B), Transmit Clock 

RS-422/V.11 

12 

23 

Input 

CTS (+/B), Clear to Send 

RS-422/V.11 

13 

27 

Input 

TxD (+/B), Transmit Data 

RS-422/V.11 

14 

22 

Output 

TxC (-/A), Transmit Clock 

RS-422/V.11 

15 

Input 

RxD (+/B), Receive Data 

RS-422/V.11 

16 

24 

Input 

RxC (-/A), Receive Clock 

RS-422/V.11 

17 

Input 

LL, Local Loopback Control 

RS-232/V.28 

18 

10 

Output 

RTS (+/B), Request to Send 

RS-422/V.11 

19 

25 

Output 

DTR (-/A), Data Terminal Ready 

RS-422/V.11 

20 

12 

Output 

RL, Remote Loopback Control 

RS-232/V.28 

21 

14 

Output 

DSR (+/B), Data Set Ready 

RS-422/V.11 

22 

29 

Input 

DTR (+/B), Data Terminal Ready 

RS-422/V.11 

23 

30 

Output 

AuxClk (-/A), DTE Clock Output 

RS-422/V.11 

24 

17 

Output 

Summary of Contents for SyncLink GT2E



















Reviews: