Microframe Corporation
12
604 South 12
th
Street
Broken Arrow, OK 74012
800-635-3811
www.microframecorp.com
Series 3500
Nexus Pager
Features
The Nexus Pager is designed to work with the MultiPage family of
on-premise transmitters. The rechargeable pager can show
unlimited numeric messages sent by the transmitter. Optionally, the
pager can show up to three factory pre-programmed text messages
corresponding to the beep type specified.
Turning on the Pager
Hold down the RED BUTTON on the side until the pager comes on.
Sending A Page
Please see the diagram in the MultiPage section of this manual for
detailed instructions on sending pages.
Activating a Pre-Defined Message
To activate a pre-defined message on a vibrating pager, type in the
pager number followed by the [SEND] key. You will be prompted for
a “BEEP TYPE (1-4).” Select 1-3 here and press the [SEND] key.
This will display on the pager one of the three pre-programmed text
messages stored in the pager. If no number is chosen, the pager will
default to Beep Type 4 (“PAGING”).
Sending a Numeric Message
To send a numeric message to a pager, simply type in the pager number followed by the [SEND] key. The transmitter
screen will display “BEEP TYPE.” Simply press [ENTER] to bypass this. The transmitter screen will then display
“ENTER MESSAGE.” Using the number keys, type in a numeric message up to 16 digits followed by the [SEND] key.
Note: If the message portion of a page is not blank the “BEEP TYPE” pre-defined message selected will be ignored.
Receiving a Page
The Nexus pager will start to vibrate when it is paged. No action is necessary on the receiving end. The pager will stop
vibrating after approximately eight seconds. If the user would like to stop the vibration before the eight seconds, simply
press the RED BUTTON on the side of the pager. If a numeric message is sent to the pager, the message will be visible
on the pager's LCD screen until the pager stops vibrating. To view the message and turn off the flashing lights, press the
RED BUTTON three times.
Sending a Group Call Page
All pagers respond to call number “900” (unless another group call number has been chosen by the customer and
programmed at the factory). To page all pagers at once, simply enter “900” and [SEND]. Then press [SEND] again at
the beep type prompt.
Manual Pager Turn-Off
Press the RED BUTTON on the side of the pager for 5 seconds or place pager on the charging base.
Lighting Function
Press the RED BUTTON on the side of the pager.
Changing the Alert Mode
Pagers may be programmed to respond to a page by flashing lights; flashing and beeping; flashing and vibrating; or
flashing, vibrating and beeping. By default, the pagers are programmed to flash and vibrate for 8 seconds.
To change the alert mode, follow these instructions: Remove all the pagers from the charging unit or unplug the power
supply that is connected to the charging base. Wait for the demo page to stop (about 7 seconds). Press "1248" followed
by [SEND] and [ENTER]. For the message, enter the code that corresponds to the alert that you want (see below.) For
example, if you want the pagers to flash only, press "1248-SEND-ENTER-9797-SEND." After sending the code, the
lights on all the pagers will flash to indicate the programming was received. Return all the pagers to the charging base or
plug the power supply back in. The pagers are ready to receive the page with the new alert.
Flash & Beep
"9595"
Flash & Vibrate
"9696"
Flash Only
"9797"
Flash, Vibrate & Beep
“9898"
CAUTION
a) The pager is made up of LCD and precision elements. Avoid water and high temperature.
b) Remove the battery if the pager will not be in use for a long period of time.
c) If the pager is not working properly, do not dismantle or repair it yourself. Call Microframe for technical service.
