Home
/
Microchip Technology
/
RN2483 LoRa
/
User Manual

Microchip Technology RN2483 LoRa, User Manual, Page: 26 / 64

Share

Page: 26 / 64

Microchip Technology RN2483 LoRa User Manual Download Page 26

RN2483 LoRa Technology Module Command Reference User’s Guide

DS40001784G-page 26



2015-2018 Microchip Technology Inc.

2.4.5

mac forceENABLE

Response:

ok

The network can issue a certain command (Duty Cycle Request frame with parameter
255) that would require the RN2483 module to go silent immediately. This mechanism
disables any further communication of the module, effectively isolating it from the
network. Using

mac forceENABLE

after this network command has been received

restores the module’s connectivity by allowing it to send data.
Example:

mac forceENABLE

// Disables the Silent Immediately state.

2.4.6

mac pause

Response: 0 – 4294967295 (decimal number representing the number of milliseconds

the mac can be paused)

This command pauses the LoRaWAN stack functionality to allow transceiver (radio)
configuration. Through the use of

mac pause

, radio commands can be generated

between a LoRaWAN Class A protocol uplink application (

mac tx

command), and the

LoRaWAN Class A protocol Receive windows (second response for the

mac tx

command). This command will reply with the time interval in milliseconds that the
transceiver can be used without affecting the LoRaWAN functionality. The maximum
value (4294967295) is returned whenever the LoRaWAN stack functionality is in Idle
state and the transceiver can be used without restrictions. ‘

0

’ is returned when the

LoRaWAN stack functionality cannot be paused.
For example, when operating in LoRaWAN Class C mode, the receiver is continuously
in receive. The

mac pause

command will return ‘

0

’ indicating that the LoraWAN stack

cannot be paused.
After the radio configuration is complete, the

mac resume

command must be used to

return to LoRaWAN protocol commands.
Example:

mac pause

// Pauses the LoRaWAN stack

functionality if the response is different
from 0.

2.4.7

mac resume

Response:

ok

This command resumes LoRaWAN stack functionality, in order to continue normal
functionality after being paused.
Example:

mac resume

// Resumes the LoRaWAN stack functionality.

Note:

The

silent immediately status

bit of the MAC status register

indicates the device has been silenced by the network. Refer to

2-1: “MAC Status bit-Mapped Register (1)”

.

Note:

If already joined to a network, this command

MUST

be called

BEFORE

configuring the radio parameters, initiating radio reception, or transmission.

Note:

This command

MUST

be called

AFTER

all radio commands have been

issued and all the corresponding asynchronous messages have been
replied.

«
...
24
25
26
27
28
...
»

Summary of Contents for RN2483 LoRa

































































Reviews:

No comments