Microchip Technology ATtiny3217 Xplained Pro Manual Download Page 16

Table 4-4. Mechanical Buttons

ATtiny3217 Pin

Silkscreen Text

Shared Functionality

PB5

SW0

EXT3

 and 

EDBG DGI

PC5

SW1/RST

EXT3

 and 

UPDI debug connector

Info: 

 PC5 is connected to a button that states 'SW1/RST' because PC5 had reset capabilities in an early

version of the ATtiny3217. Today the ATtiny3217 does not have any reset capabilities on PC5.

4.3.2 

Crystal

The ATtiny3217 Xplained Pro kit contains a 32.768 kHz crystal, which can be used as the clock source for the
ATtiny3217 device. The crystal has a cut-strap next to it, which can be used to measure the oscillator safety factor.
This is done by cutting the strap and adding a resistor across the strap. More information about oscillator allowance
and safety factor can be found in the 

AN2648

 application note from Microchip.

There is a 9 pF, 32.768 kHz crystal in a 3.2 mm by 1.5 mm package mounted on ATtiny3217 Xplained Pro.

Info: 

 The crystal is not connected to the device by default, as the crystal pins on the device are shared

with the UART module. The UART interface is lost if the crystal is needed by the application. See 

Kit

Modifications

 for instructions on how to modify the kit for crystal operation.

Table 4-5. External 32.768 kHz Crystal

ATtiny3217 Pin

Function

PB2

XOUT32

PB3

XIN32

Related Links

2.2  Design Documentation and Relevant Links

4.3.3 

LED

There is one yellow LED available on the ATtiny3217 Xplained Pro board that can be turned ON and OFF. The LED
can be activated by connecting the I/O line to GND.

Table 4-6. LED Connection

ATtiny3217 Pin

Silkscreen Text

Shared Functionality

PB4

LED0

EXT1

4.3.4 

QTouch

®

 Button

There are two self-capacitance buttons available on the ATtiny3217 Xplained Pro board, which can be used as input
buttons for an application. These QTouch buttons are intended to be driven by the built-in Peripheral Touch Controller
(PTC) of the device.

To get started using the QTouch buttons and the PTC, there is a similar example project that can be opened here: 

QTouch Tiny817 Xplained Pro Selfcap Example

 in Atmel Start (

http://start.atmel.com/#examples

). The two kits are

identical except for the device.

 ATtiny3217 Xplained Pro

Hardware User Guide

©

 2020 Microchip Technology Inc.

 User Guide

DS50002765B-page 16

Summary of Contents for ATtiny3217 Xplained Pro






























Reviews: