background image

 

 

LIMITED CARRY- IN WARRANTY 

10

 

7. 

LIMITED CARRY- IN WARRANTY 

The  following  Warranty  is  conditional  that  the  relevant  Microcare  product  has  been  installed  by  an 
approved  Microcare  Installer,  the  required  paperwork  has  been  submitted  to  Microcare  and  that  the 
Client is in receipt of our acknowledgement of this. Our products are innovative pieces of equipment 
and  incorrect  installation  has  been  the  overriding  cause  of  failure  in  the  past.  No  exception  to  this 
condition will be considered. 

Microcare warrants its full range of products against defects in workmanship and materials, fair wear and tear 
accepted, for a period of three years (Inverters manufactured from the 1

st

 July 2020 onwards carry a five-year 

warranty) from the date of collection for all equipment and is based on a carry-in basis. Where the installation 
of  the  product  makes  it  impractical  to  carry-in  to  our  workshops,  Microcare  reserves  the  right  to  charge  for 
travel time and kilometres travelled to and from the site where the product is installed.  
 
During this warranty period, Microcare will, at its own discretion, repair or replace the defective product free of 
charge. This warranty will be considered void if the unit has suffered any physical damage or alteration, either 
internally or externally, and does not cover damages arising from improper use such as, but not exclusive to:  
 

•  Reverse of battery polarity.  
•  Inadequate or incorrect connection of the product and/or of its accessories.  
•  Mechanical shock or deformation.  
•  Contact with liquid or oxidation by condensation.  
•  Use  in  an  inappropriate  environment  (dust,  corrosive  vapour,  humidity,  high  temperature,  biological 

infestation)  

•  Breakage or damage due to lightning, surges, spikes or other electrical events.  
•  Connection  terminals  and screws  destroyed  or  other  damage  such as  overheating due to  insufficient 

tightening of terminals.  

•  When considering any electronic breakage except due to lightning, reverse polarity, over-voltage, etc. 

the state of the internal control circuitry determines the warranty.  

 
This warranty will not apply where the product has been misused, neglected, improperly installed, or repaired 
by anyone else than Microcare. In order to qualify for the warranty, the product must not be disassembled or 
modified. Repair or replacement are our sole remedies and Microcare shall not be liable for damages, whether 
direct,  incidental,  special,  or  consequential,  even  caused  by  negligence  or  fault.  Microcare  owns  all  parts 
removed from repaired products. Microcare uses new or re-conditioned parts made by various manufacturers 
in  performing  warranty  repairs  and  building  replacement  products.  Microcare  repairs  or  replaces  a  part  of  a 
product; its warranty term is not extended. Removal of serial numbers may void the warranty.  
 
All remedies and the measure for damages are limited to the above.

 

Microcare shall in no event be liable for 

consequential,  incidental,  contingent  or  special  damages,  even  if  having  been  advised  of  the  probability  of 
such damages. Any and all other warranties expressed or implied arising by law, course of dealing, course of 
performance, usage of trade or otherwise, including but not limited to implied warranties of merchantability and 
fitness  for  a  particular  purpose,  are  limited  in  duration  to  a  period  of  three  years  (five  years  for  Inverters 
manufactured from the 1

st

 July 2020 onwards) from the date of purchase.  

 

 
Life Support Policy  

 
As a general policy, Microcare does not recommend the use of any of its products in life support applications 
where failure or malfunction of the Microcare product can be reasonably expected to cause failure of the life 
support device or to significantly affect its safety or effectiveness. Microcare does not recommend the use of 
any  of  its  products  in  direct  patient  care.  Microcare  will  not  knowingly  sell  its  products  for  use  in  such 
applications unless it receives in writing assurances satisfactory to Microcare that the risks of injury or damage 
have  been  minimised,  the  customer  assumes  all  such  risks,  and  the  Liability  of  Microcare  is  adequately 
protected under the circumstances.  

 
Caution  

 
While all care is taken by us to dispatch goods with adequate packaging, Microcare is not responsible for any 
damaged caused to products after they have left our premises. Semi-sealed batteries have to be transported 

Summary of Contents for 600W 12V














Reviews: