background image

 

11

Setup Menu 

The Setup function gives you access to some of the default settings used by the Copywriter Flash 
Duplicator. 

Startup Menu 

The Startup Menu selection allows you to select the main menu item that appears when the 
Copywriter Flash Duplicator starts up.  The default setting is 

1. Copy

.  Main Menu items 1 

through 6 can be selected. 

Copy Area 

Only Data Area 

With the Copy Area setting selected as 

Only Data Area

, the system will automatically 

analyze the source flash card’s file format. If the file format is FAT16/32, NTFS, Linux (Ext2, 
Ext3) file system which the duplicator recognizes then the system will only copy the content 
data instead of copying the whole flash card including the empty space. For example a 2GB 
flash card which is FAT32 file format and has only 50 MB of data inside, the system will only 
copy that specific 50MB of data. Which will only take a few seconds to copy the source.   
With the Copy Area setting selected as 

Whole Media

, the system will copy the whole flash 

card, including the empty space and format. This function is used when you have a flash 
source which has an unknown file format and you don’t want the system to be confused by 
such a format.  

Button Beep 

This setting allows you to turn 

ON

 or 

OFF

 the beep produced when the buttons are pressed.  

The default setting is 

ON

Asyn Hold Time 

This setting allows you to specify the amount of time the duplicator will wait before exiting an 
Asynchronous duplication job.  If there are no target cards detected, then the duplication will 
exit in that time period.  Options are: OFF, 5 seconds, 10 seconds, 20 seconds, 30 seconds, 
40 seconds, 50 seconds, 1 minute, 5 minutes, 10 minutes, and 20 minutes. 
This setting has no effect on Synchronous duplication. 

Ignore Size 

This setting allows you to determine how closely the capacity of the target cards match the 
capacity of the source card.  Options are: NO IGNORE (cards must be the same capacity), 
percentages ranging from 1% to 50%, or DON’T CARE (“Size doesn’t matter”).   
This setting is intended for flexibility if the source card is a low-capacity card.  Any attempt to 
duplicate more data than the target card’s capacity will fail.

 

Asynchronous 

If this setting is 

ON

 and the source’s file format is one that can be analyzed, the source card 

is read at the start of the copy process to determine the capacity of the data to be copied.  
The amount of capacity duplicated will equal the size of the source data rather than the 
capacity of the entire card.  FAT12, FAT16, and FAT32 file formats can be analyzed. 
This setting must be set to 

ON

 for the Asynchronous Duplication to operate.   

If your source is in a file format that can’t be analyzed, such as NTFS, this setting must be 

OFF

 for duplication to occur.   

If this setting is 

OFF

, the entire capacity of the source card will be duplicated to the target 

cards, resulting in longer duplication times. 

Language 

Sets the language on the display.  The default is English.

  

Summary of Contents for Copywriter Flash Duplicator














Reviews: