background image

Micro-Trak

®

 Warranty

Micro-Trak  (herein  “Seller”)  warrants  to  the  original  purchaser  (herein  “Buyer”)  that,  if  any  product  or  part  of  the  product 

(herein “part”) proves to be defective in material or workmanship, upon inspection and examination by Seller, within one (1) 

year from the original date-of-purchase, and is returned to Seller with dated proof-of-purchase, transportation prepaid, within 

thirty (30) days after such defect is discovered, Seller will, at their option and sole discretion, either repair or replace said part, 

except that the warranty for expendable parts, including but not limited to, light bulbs and batteries shall be thirty (30) days 

from the original date-of-purchase. Said warranty is valid only when the part has been installed, operated and maintained in 

strict accordance with the procedures outlined in the manual. Any damage or failure to said part resulting from abuse, misuse, 

neglect, accidental or improper installation or maintenance, unauthorized modification, use with other products or attributable 

to acts of God, as determined solely by the Seller, will invalidate the warranty.  Said part will not be considered defective if it 

substantially fulfills the performance specification. Buyer shall be responsible for all maintenance services, if any, all in strict 

accordance with the procedures outlined in the manual. The warranty does not include labor, installation, replacement parts 

or repairs, delivery of replacement parts or repairs or time and travel. Said warranty is nontransferable.

ThE FOREgOINg wARRANTy IS ExCLUSIvE ANd IN LIEU OF ALL OThER wARRANTIES OF MERChANTABILITy, FITNESS FOR 

PURPOSE ANd OF ANy OThER TyPE, whEThER ExPRESS OR IMPLIEd.

 The Seller’s liability, whether in contract, in tort, under 

any warranty, in negligence or otherwise, shall not exceed the return of the amount of the purchase price paid by the Buyer, 

and under no circumstance shall the Seller be liable for special, indirect or consequential damages. Seller neither assumes nor 

authorizes anyone to assume for it any other obligation or liability in connection with said part. No action, regardless of form, 

arising out of the transactions under this agreement may be brought by the Buyer more than one (1) year after the cause of 

action has occurred.
Seller agrees to extend the term of the foregoing warranty period should the Buyer return completed warranty registration 

information, with dated proof-of-purchase, to the Seller within one (1) year from the original date-of-purchase. All conditions 

and limitations of said foregoing warranty, except the term of said foregoing warranty, shall apply. Said term shall be extended 

to a total of three (3) years from the original date-of purchase on display consoles and network communication modules, as 

defined by Seller, and said term shall be extended to a total of two (2) years from the original date-of-purchase on all other 

parts, except that the warranty for expendable parts, including but not limited to, light bulbs and batteries shall be thirty (30) 

days from the original date-of-purchase, and except that the warranty for parts manufactured by someone other than the 

Seller, including but not limited to, shut-off and control valves, DGPS receivers, memory cards and drives, mapping software, 

flowmeters and pressure sensors shall be one (1) year from the original date-of-purchase.
Buyer accepts these terms and warranty limitations unless the product is returned to Seller, via proper distribution channels 

and approved return authorization, with dated proof-of-purchase, transportation prepaid, within fifteen (15) days from the 

date-of-purchase for refund of the purchase price.
Units  under  warranty  should  be  sent  prepaid,  with  dated  proof-of-purchase,  within  30  days  of  discovering  defect,  to  the 

address below:

MAIL ANd UPS:

Micro-Trak Systems, Inc. 

ATTN:  Service department

P.O. Box 99 

111 East LeRay Avenue 

Eagle Lake, MN 56024-0099

At Micro-Trak Systems, we believe a product that delivers quality and performance at a low cost is what is needed to help 

today’s operator and the operator of the future compete in the world mar ket.
It  is  our  goal  to  provide  operators  with  a  line  of  electronic  equipment  that  will  help  build  and  maintain  an  efficient  and 

profitable operation that can be passed on to future generations.
We thank you for your purchase and hope that we can be of service to you in the future.
Micro-Trak Systems, Inc.

Extended warranty Option

It’s simple!  Just complete the enclosed registration card(s) for this

 product and mail it in and we’ll extend your warranty for up to three years*, at no additional charge.

MAIL IN yOUR REgISTRATION CARd(S) TOdAy!

Registration Card information is for internal use only.

* Some limitations apply. See warranty statement for details.

3

Summary of Contents for MT-3405 M

























































Reviews: