background image

- 1 - 

 

Mianyang Weibo Electronics Co.,Limited 

No.98 Youxian East Road, Youxian District, Mianyang City, P.R. China 

Tel: 86-0816-2971265 Fax: 86-016-2281934 

www.mywbdz.com      [email protected] 

WBV412U01 AC Voltage Transducer 

Safety claim 

The information in the safety claim of the equipment documentation is intended to ensure that equipment 

is properly installed in order to maintain it in a condition. 

It is assumed that everyone who will be associated with the equipment will be familiar with the contents of 

that safety section, or this safety guide. 

When  electrical  equipment  is  in  operation,  dangerous  voltages  will  be  present  in  certain  parts  of  the 

equipment (e.g. the input terminal). Failure to obverse warning notices, incorrect use, or improper use 

may endanger personnel and equipment and course personal injury or physical damage. 

Before working in the terminal strip area, the equipment must be isolated. 

Proper  and  safe  operation  of  the  equipment  depends  on  appropriate  shipping  and  handling,  proper 

storage, installation and commissioning, and on careful operation, maintenance and servicing. 

The  operating  manual  for  the  equipment  gives  instructions  for  its  installation,  commissioning,  and 

operation.  However,  the  manual  cannot  cover  all  conceivable  circumstances  or  include  detailed 

information on all topics. In the event of questions or specific problem, do not take any  action  without 

proper  authorization.  Contact  the  appropriate  WB  technical  or  sales  office  and  request  the  necessary 

information.   

 

Standard application 

1. Accuracy 

    Accurate degree is conformed to IEC688:1992 

2. Safety 

2.1 Overload capability 

      Overload capability is conformed to IEC688:1992 

2.2 Isolation voltage 

Can be endured testing voltage is conformed to Q/72085584-0.1-2004 

2.3 Insulation impedance 

The insulation impedance is no less than 20M Ohm, is conformed to Q/72085584-0.1-2004     

3. Electromagnetic Capability   

        3.1. Electromagnetic field immunity test according to IEC 61000-4-3:1995 

        3.2 Power frequency magnetic field immunity test according to IEC 61000-4-8:1993     

 

 

 

Summary of Contents for WBV412U01








Reviews: