MHC Medical Products Easy Touch User Manual Download Page 35 | Manualshive

Page: 35 / 52

background image

33

Transfer Test Results to a Computer

You can use your meter with EasyTouch

®

Link Health Management Software

to transfer test results to your personal computer:

1. Obtain the required software and cable

Download software at MHCmed.com. To order a cable, call Customer

Service at 1.877.358.4342 (Mon-Fri, 9am–5pm, EST)

2. Install the software on a computer

Follow the instructions provided with software to install the software.

3. Get ready to transfer test results

Connect the interface cable to a serial port on your computer. Then

connect the other end of interface cable to the data port located on

the side of the meter

with the meter turned off

. “PC” will appear on

the display, indicating that the meter is in the communication mode.

4. Transfer data

Follow the instructions provided in the software to download the results

from the meter. After finishing the data transfer, press

button

to turn

off the meter.

Note: You will be unable to perform a blood glucose test in PC link mode.

The meter will only respond to computer commands while in PC link mode.

«
...
33
34
35
36
37
...
»

Summary of Contents for Easy Touch





















































Reviews:

No comments

Related manuals for Easy Touch

Brand: Sejoy Pages: 50

Brand: i-SENS Pages: 35

Brand: Apollo Pages: 37

metaReach UMB305-0510

Brand: RichHealth Pages: 47

Brand: Microdot Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands