background image

Color-coded 6 mm.

BLUE

outlet Quick-Connect union

connects to the cannula or

face mask

Color-coded 4 mm.

RED

inlet Quick-Connect

union connects to

the primary reducing

regulator

Power On/Off

and Control

Switch

Operational and

precautionary

front face-place

Audio port.

Sound from

flow-fault

and

apnea

conditions only

POSITIVE

FLOW

!

FLOW FAULT

APNEA

LOW BATT

STATIC PORTS

DO NOT COVER

EDS MODEL D1

MH

INLET TO

SUPPLY / CYLINDER

OUTLET TO

CANNULA / FACE MASK

Green LED

Red LED

Static ports

DO NOT COVER

EDS-D1

Page 2 of 8

High brightness green

LED for indication of

positive flow of

oxygen for each

inspiration effort.

High brightness

red LED for

indication of

oxygen

flow-faults,

apnea and low

battery condition.

External Battery

Cannula

Inside (tip) is neg (-)

Outside (ring) is pos (+)

EDS Unit

EPS

11 - 28 VDC input

The EDS-EPS is a floating 
ground unit suitable for 
negative or positive ground 
systems.  Be sure to ground it 
to the main system ground.

System Ground

1

2

3

9 Volt

A l k a l i n e

Replacing the battery in the EDS unit

Remove the battery door by holding the unit with both hands
and pressing in with your thumbs at the point of the arrow
pushing in while pushing door outwards (fig 1.)  This is best
done if the unit is held with the battery door facing up at you
and out.  The EDS-D1 unit uses a standard 9 (nine) volt
alkaline battery connector system.  This is a very positive-
connecting type connector that requires a bit more force to
connect and disconnect to the battery.  This is a superior type
connector for equipment subjected to rough out-door
treatment.  Therefore, please take extra care in removing and
replacing the battery making sure not to pull on the wires.
Use only alkaline type batteries with the EDS-D1 unit.

If the EDS -D1 unit will be

operating outside in very cold

temperatures, premature

battery depletion may be

likely. An external battery

connector can be wired up to
use an external 9 volt battery

placed somewhere warmer

such as your flight suit. It

can also be used as an

emergency backup,

electronically replacing the

internal battery with the

external battery that is

plugged in the external jack..

Up to (8) eight  EDS-D1 units can
be powered from our optional EPS
(External Power Supply) unit if it is
desirable to use the power system
from an aircraft. The EPS is a 10
volt @ 500 ma. low-drop-out
voltage regulator and filter unit that
operates from 11 to 28 volts. It
filters out glitches caused by
hydraulic pumps, strobe lights and
other high-energy devices. It works

Summary of Contents for EDS-D1













Reviews: