8
9
6)
General power tool safety warnings- Service
• Have your power tool serviced by a qualified repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs.
Service of battery packs should only be
performed by the manufacturer or authorized service providers.
• Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpected situations.
7)
Impact Driver Safety Warnings
•
Avoid prolonged contact with dust from construction activities like power sanding,
sawing, grinding, and drilling. Always wear protective clothing and immediately wash
any exposed areas with soap and water.
SPECIFIC SAFETY RULES
STAY ALERT
• Exposure to loud noise can cause hearing damage.
Always wear ear a protection when
using power equipment.
WARNING: ALWAYS use safety glasses.
Everyday eye glasses are NOT safety glasses.
• Use face or dust mask if operation is dusty.
ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI SI 2.6 (S3.19) hearing protection
• NIOSH/OSHA respiratory protection
Watch what you are doing and use common sense. Don't operate any tool when you are
tired.
WARNING: Some dust created when using power tools to sand, grind, drill or saw
and/or other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm. Some examples of these types
of chemicals:
• lead from lead-based paint
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies depending on how often you do work that involves
these materials.
To reduce exposure risk, work in a well ventilated area with approved safety equipment like
dust masks that are designed to filter out microscopic particles.
WARNING: Changes or modification to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
This limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and radiate radio frequency energy
and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communication. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on,
the user in encouraged to try to correct the interference by one or more of the following
measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
is connected.
. Consult the dealer or an experienced radio /TV technician for help.
Hold power tools by insulated gripping surfaces, when performing an operation where
the fastener may contact hidden wiring. Fasteners contacting a
″
live
″
wire will make
exposed metal parts of the power tool
″
live
″
and could give the operator an electric
shock.
Avoid unintentional starting. Prepare to begin work before turning on the tool.
Do not lay the tool down until it has come to a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
When using a handheld power tool, maintain a firm grip on the tool with both hands to
resist starting torque.
Do not leave the tool unattended when the Battery Pack is connected. Turn off the tool,
and remove the Battery Pack before leaving.
The battery Charger gets hot during use. The Charger’s heat can build up to unsafe levels
and create a fire hazard if it does not receive adequate ventilation, due to an electrical
fault, or if it is used in a hot environment. Do not place the Charger on a flammable surface.
Do not obstruct any vents on the Charger. Especially avoid placing the Charger on
carpets and rugs; they are not only flammable, but they also obstruct vents under the
Charger. Place the Charger on a stable, solid, nonflammable surface (such as a stable
metal workbench or concrete floor) at least 1 foot away from all flammable objects, such
as drapes or walls. Keep a fire extinguisher and a smoke detector in the area. Frequently
monitor the Charger and Battery Pack while charging.
This product is not a toy. Keep it out of reach of children.
People with pacemakers should consult their physician(s) before use. Electromagnetic
fields in close proximity to heart pacemaker could cause pacemaker interference or
pacemaker failure.
The warnings, precautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
FCC SAFETY
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause Harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
20V ULTRA Impact Driver 2Ah KIT
(MH-03-ID-B1-0-1)
20V ULTRA Impact Driver 2Ah KIT
(MH-03-ID-B1-0-1)