manualshive.com logo in svg

MGE UPS Systems 11+, Installation And User Manual

Share
Download
MGE UPS Systems 11+ Installation And User Manual Download Page 15

Introduction

Thank you for selecting an MGE Office Protection Systems product to protect your electrical equipment.

The product you selected is a part of the EX RT series. The EX RT series is a family of Uninterruptible Power Supply
(UPS) designed to provide safe, and reliable AC power back-up for sensitive electrical equipment. To discover the
entire range of MGE Office Protection Systems products, we invite you to visit our website at www.mgeops.com.

1.0

Scope

Introduction is a general description of system configurations of the EX 5/7/11 RT, and its mechanical electrical
characteristics. Additionally there is an optional accessories section with important information on MGE Office
Protection Systems products that will enhance the performance of the EX 5/7/11 RT. Please contact your MGE
Office Protection Systems representative for detailed information on these options.

Table 1-1: EX RT Model Descriptions and Contents.

Also: All units include rail kits for rack mounting and stabilizing feet for tower configuration.

NOTE

The Power Module is factory configured for single Mains input at 208VAC, 
60Hz. Other input-output voltage settings are available. See Section 3.2.1. 
Input voltage must be the same as output voltage on HV units!

System Description

System Contents

Output Voltage

Model #

Part #

Power Module

Battery Module

Transformer

Module

86215

86216

86217

86207

86209

86211

86311

5 kVA

HV EX 5RT

86050

X

X

200/208/220/

230/240/250

5 kVA

LV EX 5RT

86201

X

X

X

120/208/240

7 kVA

HV EX 7RT

86070

X

X

200/208/220/

230/240/250

7 kVA

LV EX 7RT

86203

X

X

X

120/208/240

11 kVA

HV EX 11RT

86110

X

X

200/208/220/

230/240/250

11 kVA

LV EX 11RT

86205

X

X

X

120/208/240

1 — 1

86-86000-00 B01

Introduction

Summary of Contents for 11+













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands