MFM blwhndmtma6nk User Manual Download

Page: 13 / 15

Petrol Powered Backpack Blower

E&OE

Troubleshooting

Problem

Probable Cause

Corrective Action

Engine does not start, or
starts but will not run

Incorrect starting procedures

Follow instructions in the user manual

Incorrect carburettor mixture

Have carburettor adjusted by an authorised
service centre

Fouled spark plug

Clean/gap or replace plug

Empty fuel tank

Fill fuel tank with properly mixed fuel

Primer bulb was not pressed
enough

Press primer bulb fully and slowly ten times

Engine starts, but has low
power

Fuel filter is plugged

Replace spark arrestor screen

Incorrect lever position

Move to run position

Dirty spark arrestor screen

Replace spark arrestor screen

Dirty air filter

Remove, clean and reinstall filter

Engine hesitates

Incorrect carburettor mixture setting

Have carburettor adjusted by an authorised
service centre

Air filter is plugged

Replace or clean the air filter

Old or improperly mixed fuel

Drain gas tank/add fresh fuel mixture

Air filter is plugged

Replace or clean the air filter

Fouled spark plug

Replace or clean the spark plug

Incorrectly gapped spark plug

Clean/gag or replace plug

Dirty air filter

Clean or replace air filter

Smokes excessively

Incorrect carburettor mixture setting

Have carburettor adjusted by an authorised
service centre

Summary of Contents for blwhndmtma6nk
















Search results

Summary of Contents for blwhndmtma6nk

Reviews:

Related manuals for blwhndmtma6nk

Brands by name

Popular brands

MFM blwhndmtma6nk, User Manual

Search results

Summary of Contents for blwhndmtma6nk

Reviews:

Related manuals for blwhndmtma6nk

Brands by name

Popular brands