MFJ MFJ-422E Instruction Manual Download Page 9

MFJ-422E/422EX Instruction Manual 

Electronic Keyer Paddle 

 
A self test is included to perform testing of the paddle, the buttons, the controls, 
and the audio circuitry.  At any time, turn off the power to stop the self test. 
 
To perform this test: 
1.  Turn off the power and remove the power plug. 
2.  Push all buttons so they are in the out position. 
3.  Turn all knobs to full clockwise position, except the Volume control.  Set 

volume to a comfortable listening level. 

4.  Remove the case by removing the screws on the bottom that secure it to the 

paddle. 

5.  Remove jumpers JMP4 to JMP7.  Set jumper JMP3 to the "B" position.  Set 

jumpers JMP8 and JMP9 to the "H" position. 

6. Reconnect 

power. 

7.  Squeeze the paddle while turning the power on.  The self test starts by 

sending the copyright message 

"COPYRIGHT 1996-XXXX MFJ ENTERPRISES, 

INC.  VERSION X.XX"

 confirming the audio circuitry is working properly.  

Release the paddle before the message is finished.  For the entire test, the 
LED should blink once after each operation.  If the LED blinks 
continuously the unit fails the test and a Morse code message is sent to 
indicate the nature of the failure. 

8.  The paddle, the buttons, and jumpers JMP3 to JMP9 are automatically 

tested for shorts to ground.  The LED should be off at this point. 

9.  Press and release the dot level; press and release the dash level. 
10.  Press and release the 

Message

 button. 

11.  Lock in the 

Semi-Auto/Auto

 button, then press and release the dash level. 

12. Test the 

Speed

 control by turning it to full counter-clockwise then to full 

clockwise.  The LED should blink once at each end. 

13. Test the 

Weight

 and 

Tone

 controls in the same way.  The LED should 

blink once at each end. 

14.  Test the jumper connections by placing the plug-in jumpers on the "A" 

position of JMP3 and the "L" positions of JMP4 to JMP9 in ascending 
order.  The LED should blink once for each jumper. 

15.  When all is okay, a repetitive message 

"PASS"

 is sent to the speaker.  A 

repetitive message such as 

"SP FAIL"

 indicates that you did not follow the 

correct order or the unit failed the test. 

16.  Turn off the power after confirming the audio has good quality and remove 

the power plug. 

17.  Replace all jumpers to their original positions. 
18.  Replace the case on to the paddle and secure it with the screws. 
19.

 

Reconnect power and resume with normal operation. 

Memory Test 

 

Summary of Contents for MFJ-422E

















Reviews: