MFJ MFJ-422E Instruction Manual Download Page 7

MFJ-422E/422EX Instruction Manual 

Electronic Keyer Paddle 

Embedded Commands: 

While in the message recording mode you may use embedded commands for 
special features.  To use an embedded command simply store the multi-
character embedded command code within your message. 
 

/D

 

Decrement-decrements the serial number.  Serial number 0001 will 
decrement to 9999, skipping 0000 since it is not used.  This feature 
allows a serial number to be sent twice in a message. 

 Example: 

 

UR RST 559 559 SN /N /D SN /N 

/G

#

 

Gap-inserts a gap of 

#

 standard intra-character spaces into the message, 

where 

#

 is a digit in the range of 1 to 9 (0 can be used but not 

practical).  Invalid numeral code will automatically default to zero.  
This command is used to exaggerate inter-character and word spacing. 

/L

 

Loop-creates a message loop (message repeat).  Note that any character 
recorded after "/L" will not be sent. 

 Example: 

 

BEACON AA5CS 5 W /L 

/N

 

Number-inserts a contest serial number, in the range of 001 to 9999, 
into the message.  Jumpers JMP4 to JMP8 controls the way zeroes and 
nines in the serial number are sent.  Only three digits are sent for 
numbers less than 1000--use leading zeros when appropriate.  The 
serial number is automatically post-incremented each time it is sent and 
updated in the non-volatile memory.  Serial number 9999 will wrap-
around to 0001, skipping 0000 since it is not used.  The serial number 
is set to the same one as before when power on.  If a different serial 
number is desired, it must be programmed during power up.  To 
initialize the serial number, press and hold the 

Message

 button while 

turning the power on until the keyer plays "GO" (dah-dah-dit dah-dah-
dah) and the LED flashes.  You must then enter 

four

 numbers in Morse 

code for a valid serial number, most-significant digit first (invalid 
numeral code will automatically convert to zero).  All numbers must be 
in the proper Morse code format.  For example, the number "1" must 
be "di-dah-dah-dah-dah" and the number "0" must be "dah-dah-dah-
dah-dah".  When four numbers are entered, the keyer will 
automatically send an end of message character "+" (di-dah-di-dah-dit).  
The keyer then resumes with normal operation when the LED stops 
flashing.  The serial number can be set from 0000 to 9999 (0000 will 
automatically convert to 0001). 

 Example: 

 

YOU ARE CONTACT NR /N 

Summary of Contents for MFJ-422E

















Reviews: