background image

h

   43

Transport of people inside a mo-
tor vehicle

To determine if your electric wheelchair is 
approved as a seat for person transport in-
side a motor vehicle, please look at the type 
plate of your electric wheelchair.

 

Therefore view chapter 

Meaning of 

the labels on the electric wheelchair

 on 

page 62.

 

Electric wheelchairs that are not suited 
for use as a seat for transport in a motor 
vehicle are marked with an additional 
label. – For this observe chapter 

Mean-

ing of the labels on the electric wheelchair

 

on page 62.

 

Observe the guideline < 

Safety with 

Meyra-wheelchairs, also during transport 
in motor vehicles

 >! – This document and 

further information can be accessed on 
our website < 

www.meyra.com

 > in the 

Download Archive

 >.

People transportation acc. to ISO 7176-19 is 
only permitted with the following anchor-
ing systems:

 

– 4-point anchoring system acc. to 

ISO 10542,

 

– Dahl Dockingstation MK II,

 

– Dahl VarioDock.

LOADING AND 

TRANSPORTATION

Do not use the back support, leg sup-
ports, arm supports or revetments to lift 
the electric wheelchair!
The electric wheelchair must be switched 
off before lifting!
The parts detached for loading must be 
carefully stowed and carefully attached 
again before the next journey.
No special carrying points are allocated 
for carrying detachable components.

The following procedures may be necessary 
due to lack of space for the transport in ve-
hicles:

 

Remove head support.

 

Remove the leg supports.

 

Fold the back support down to the 
front.

Loading

The electric wheelchair can be loaded with 
the aid of ramps or lifting platforms.

Ramps and lifting platforms

Observe the operating manual for the 
ramp or lifting platform.
Observe the manufacturer's information 
for the ramp or lifting platform.
The maximum bearing height specified 
for the ramp must be greater than the 
height 'h' from the ground to the loading 
surface, e.g. of the car.
The load capacity of the ramp or lifting 
platform must be higher than the overall 
permitted weight of the electric wheel-
chair.
There is a danger of tilting when driving 
backwards on ramps!

Summary of Contents for 1.650 iCHAIR MEYLIFE





































































Reviews: