Metso jamesbury B, Installation Maintenance And Operating Instructions

Page: 8 / 12

IMO 7/18
8 IMO-213 EN
3. Insert the four hex head cap screws (6) and lockwashers
(7) into the tapped holes. Tighten to values in Table 5.
5.5 Actuator versus Valve Position
IMPORTANT: The actuator and valve position must agree
before further assembly.
Since the valve has already been set in the closed position
(Step 1 under Valve Preparation), make sure that the actuator
is also in the closed position. EXCEPTION: if mounting a
spring-return actuator for “spring-to-open” operation; cycle
the valve to the open position and proceed with the actuator
AND valve in the open position.
5.6 Coupling to Actuator
Key Drive Actuators (Figure A): Install the key (4) into the key
slot of the coupling (1). The key should be filed to closely fit
into coupling and actuator keyway. If the fit is loose, apply
Loctite® Keyfit or equivalent.
Male/Female Square Drive Actuators (Figure C): No coupling
prep required.
5.7 Bracket Attachment to Actuator
1. Place the actuator onto the valve and bracket assembly
aligning the holes in the bracket with the holes in the
actuator, and aligning the actuator drive with the
coupling. Install the four hex head cap screws (8) and
four lockwashers (9) through the bracket and into the
actuator. Apply slightly more than finger-tightness to
these fasteners, but DO NOT TIGHTEN.
2. Cycle the actuator a couple of times, allowing the
assembly to position itself for proper actuator-drive to
valve-drive alignment. Tighten the four hex head cap
screws (8) securing the bracket to the actuator using the
values in Table 5 or 6 as applicable.
TABLE 5
Bolt Size
Torque to Cast/Ductile Body Actuators
No Lubrication
ft•lbs in•lbs N•m
1/4 8 96 11
5/16 16 192 22
3/8 27 324 37
7/16 45 540 61
1/2 67 804 91
9/16 100 1200 136
5/8 135 1620 183
3/4 225 2700 305
7/8 335 4020 454
1 520 6240 705
1-1/8 700 8400 949
1-1/4 990 11880 1342
M6 7 84 9
M8 14 168 19
M10 28 336 38
M12 48 576 65
M16 115 1380 156
M20 225 2700 305
M30 783 9396 1062
M36 1347 16164 1826
TABLE 6
Bolt Size
Torque to Aluminum Body Actuators
No Lubrication
ft•lbs in•lbs N•m
1/4 6 72 8
5/16 12 144 16
3/8 20 240 27
7/16 30 360 41
1/2 50 600 68
9/16 70 840 95
5/8 90 1080 122
3/4 160 1920 217
7/8 250 3000 339
1 360 4320 488
1-1/8 520 6240 705
1-1/4 700 8400 949
M6 5 60 7
M8 11 132 15
M10 22 264 30
M12 38 456 52
M16 90 1080 122
M20 170 2040 230
M30 570 6840 773
M36 950 11400 1288
5
3
10
2
9
8
1
1
6
7
FEMALE
MALE
Figure C Linkage Assembly – Square Drive
5.8 Open/Close Position Adjustment
NOTE: Refer to the appropriate Installation, Maintenance, and
Operating Instructions (IMO) for specific directions on how to
adjust the actuator travel stops or limit switch (see Table 7).