manualshive.com logo in svg

Metso Outotec Lokotrack ST3.8, Driving Instruction, Page: 17 / 36

Share
Download
Metso Outotec Lokotrack ST3.8 Driving Instruction Download Page 17

DRIVING INSTRUCTIONS

DRIVING INSTRUCTIONS

D100014840-EN

407 0 EN 2021-06-22

13

3. Connect the drive control device cable into either of the cable connecting sockets. There is one at the

front of the machine (1), and the other one at the rear of the machine (2).

2

1

Figure 17: Driving socket location

NOTICE:

• If a fault is detected in the connection of the drive control device

plug to the socket, an alarm is displayed on the control panel. To

acknowledge the alarm, disconnect and reconnect the drive control

device plug.

• The drive control device cannot be used if the radio control mode is

switched on.

4. On the main control panel, make sure that the radio control mode ON/OFF switch is in position 0

(OFF).

Figure 18: Radio control switch in position 0 (OFF)

1.8.2. CONNECTING THE RADIO CONTROL DEVICE

NOTICE:

Before using the radio control device, check if the local laws and regulations

allow the use of radio signals.

1. Activate the radio control device: On the main control panel, turn the radio control mode ON/OFF

switch to position 1 (ON).

Summary of Contents for Lokotrack ST3.8





































Reviews:

No comments