background image

 

 

Page 15 

 

 

 

 

Tripod Turnstile Technical Manual 

 NOTE 

 

Make sure that Power/Network cable is connected to the distribution board. 
 

 

 Network connection 

 
The  network  connection  provides  for  operational  functionality  of  the  Tripod  Turnstile.  Different 
devices in  parallel can be  connected to the  Network Controller by a single unshielded twisted pair 
(UTP) cable. Total length of the twisted pair cable is limited to 1 km. One Network Line Terminator 
must be connected at the far end of the network cable. 

 

 

OPTION I: 

Connect  the  twisted  pair  network  cable  to  designated 
terminals. The terminals are marked as “

C_L

 for network 

low signal and “

C_H

 for network high signal. 

 

 

OPTION II: 

Connect  the  twisted  pair  network  cable  with  RJ-45 
connector to one of RJ-45 connectors on the “connection 
board”.

  

 

 

 

 NOTE FOR OPTION II 

 

There  are  2  equivalent  UTP  connectors  for  Metra  NET  Network  connection.  One  can  be  used  as 
“trunk  line  IN”  and  the  other  as  “trunk  line  OUT”  connector.  Take  into  consideration  that  if  you 
disconnect one of the UTP cables (in or out), you also cut off the “trunk line” and devices after this 
device  will  be  disconnected  from  the  Metra  NET  Network.  Therefore  this  type  of  connection  is 
recommended only if you use Master and Slave Network Controllers TCP/IP, each on one side of the 
“trunk line”. 

 

 NOTE 

 

 

Mind the polarity of the network connection! 

 

Always connect the line terminator at the far end of the network cable! 

 
 

 
 
 
 
 

Summary of Contents for Tripod
































Reviews: