Metra Electronics 99-7627HG Installation Instructions Manual Download Page 6

99-7627HG

Connections to be made

• If you wish to add an aftermarket backup camera or external video source, 

connect the 

Yellow

 RCA jack labeled 

“Backcam”

 into the desired source.

• 12-pin pre-wired ASWC-1 harness:

This harness is to be used along with the optional ASWC-1 (not included) to

retain steering wheel audio controls. If the ASWC-1 is not being used, disregard

this harness. If it will be used, please refer to the ASWC-1 instructions for radio

connections and programming.

Note: Disregard the harness that comes with the ASWC-1.

Note: Disregard the RCA jack labeled “FROM DVD”, 

it will not be used in this application.

From the 12-pin harness with (4) jacks to the aftermarket radio 

(for BOSE sound-systems only):

• Connect the 

Blue/White

 wire to the amp turn on wire (this wire must be

connected to hear sound from the factory amplifier).

• Connect the 

White, Gray, Green, and Purple

 RCA jacks to the audio outputs. 

White

 is left front, 

Gray

 is right front, 

Green

 is left rear, and 

Purple

 is right rear.

For models 

without

 a BOSE sound-system:

• Connect the 

White

 wire to the left front positive speaker output.

• Connect the 

White/Black

 wire to the left front negative speaker output.

• Connect the 

Gray

 wire to the right front positive speaker output.

• Connect the 

Gray/Black

 wire to the right front negative speaker output.

• Connect the 

Green

 wire to the left rear positive speaker output.

• Connect the 

Green/Black

 wire to the left rear negative speaker output.

• Connect the 

Purple

 wire to the right rear positive speaker output.

• Connect the 

Purple/Black

 wire to the right rear negative speaker output.

For models 

with

 a BOSE sound-system:

• Tape off and disregard the 

White, White/Black, Gray, Gray/Black, Green, 

Green/Black, Purple, Purple/Black

 wires, they will not be used in this 

application.

• If you wish to retain the factory AUX-IN jack, connect the 

Red

 and 

White

 RCA

jacks labeled 

“AUX input”

, to the AUX-IN jack 

(if applicable)

.

• Tape off and disregard the 

Red

 and 

White

 RCA jacks labeled 

“FROM DVD”

, they

will not be used in this application.

• Tape off and disregard the 

Yellow

 RCA jack labeled 

FROM DVD

, it will not be

used in this application.

Summary of Contents for 99-7627HG











Reviews: