Electric heated Pasta-Cooker (600) 11/25
– Connect the metallic structure of every electrical
appliance installed to the terminals, marked by
the symbol
, and located next to the earth
terminals (unipotential system).
Connection to the water piping
– Waterfilling with water tap command on the
front side of the appliance. Water inlet pipe
connection ISO 7/1 R3/8.
The water supply must be fed at a pressure of
between 150 and 250 kPa.
Water draining
– Water drain tap command on the front side of
the appliance. Drain pipe connection: non-
threated Ø 18 mm, sink type siphon joint.
START
-
UP
Function check
– Start-up the appliance following the instructions
given; check function regularity and make sure
that the controls and heating elements are in
good working order, testing them with the
various function positions.
– The appliance has an internal safety thermostat
that switches the heating elements off when the
work thermostat is failing. In case this
thermostat cuts off, remove the screw sealing
the thermostat access hole on the control panel.
Reset the thermostat, pressing with a pointed
tool (e.g. slender screwdriver).
Nominal heat input check
– After installation and at each maintenance
intervention check the heat input of the appliance.
– The nominal heat input is stated in the
“Technical data” table.
– The appliance operates at the nominal heat input
when the electrical power is the one stated in Table T1.
ATTENTION If the power supply value is not
within the limits indicated in Table T1, interrupt
the operation of the appliance and contact the
electricity delivery body.
ANALYSIS
OF
SEVERAL
FAILURES
Heating elements do not heat up
– Check fuse valves
– Main switch off
– Insufficient power or wrong electrical connection
– Regulation thermostat faulty
– Safety thermostat activated or faulty.
Diffcult or lacking temperature adjustment
– Regulation thermostat faulty
– Wrong connection or heating elements faulty
(replace faulty element).
REPLACEMENT
OF
PARTS
SUBJECT
TO
CHANGE
IMPORTANT Before carrying out repairs, unplug
appliance from mains disconnecting the main
INSTALLATION INSTRUCTIONS
WARNINGS
Installation, adjustments and maintenance of the
appliances must be done by authorized installers,
in accordance with the safety standards in force.
The manufacturer declines any responsibility
if such obligation is not observed.
INSTALLATION
Positioning
– The overall/connection dimensions and the
technical data are stated in the pages in the
appendix.
– Install the appliances only in sufficiently aired
rooms.
– Position appliances at least 10 cm from the
nearby walls. Such distance can be less when
the walls are incombustible or protected by a
thermal insulator.
– The appliances are not suitable for built-in
installation.
Assembly
– Remove the film which protects the external
panels. Any glue remaining on these is to be
removed with a suitable solvent.
– Assemble the spacer (if foreseen) by following
the instructions enclosed with the spacer itself.
In line union of the appliances
– Put the appliances next to eachother and level
them at the same height.
– Unite the appliances using the special union
joint-coverings supplied upon request.
Electrical connections
– Appliances are designed to operate at the voltage
indicated on the rating plate.
– Each appliance must be connected to an
independent mains supply of suitable capacity
(total power indicated in “Technical data” table)
via an input terminal board with flexible rubber
cable, insulated at a level not below H07RN-F.
– Make sure that the cables lenght allows for the
live wires to disconnect from terminal block
before the yellow/green ground wire, in case of
simultaneous pull.
– Automatic cutout omnipolar switches of suitable
capacity (with contacts opening to at least 3
mm) and highly sensitive automatic differential
protective devices must be fitted. These must
ensure that there is no direct or indirect contact
between live components and fault currents
and the ground, in accordance with current
regulations (maximum admissible leakage
current 1 mA/kW).
Earth and unipotential connections
– Appliances must be earthed on terminals marked
with the symbol .
