manualshive.com logo in svg

METHVEN Aroha 01-9106, Installation Manual

Share
Download
METHVEN Aroha 01-9106 Installation Manual Download Page 17

Methven Australia Pty Ltd

ABN 15 104 813 390

Melbourne, Australia

www.methven.com

Note: It is the responsibility of the installer to ensure a water proof 

seal is achieved between the faceplate and the finished surface of the 

wall. If in any doubt about the quality of the seal, the faceplate should 

be removed and then reinstalled using silicone to ensure a seal is 

achieved.

WMKA21005

IMPORTANT

Please read all of the instructions before installation

MA019342

      

Aroha 3 Hole Wall Mounted  

Bath Set

01-9342

Use of this product is recommended for domestic and commercial applications.

All pipework must be thoroughly flushed prior to the installation of the mixer.

Inline filter washers must be installed on both hot and cold supplies to prevent foreign particles 

damaging the ceramic head works.

Do not remove the ceramic head works from the mixer when installing.

Methven recommends a licensed plumber carry out all installations in compliance with  

the requirements of AS/NZS 3500. This product complies with AS/NZS 3718 regulations.

JUNE 2012

Installation Guide

Installation 

1.   Screw the breech set (1) into the  

mounting stud. Refer to 

illustration 1. for minimum and 

maximum tolerances. Plumb the 

breech set (1) into system.

2.  A hole diameter of 35mm will 

be required for correct head 

works (2) installation and a 

hole diameter of 25mm will be 

required for correct spout (10) 

installation.

3.  Screw head works (2) into 

breech (1).

4.  Trim brass nipple (3) to length 

with a max 15mm protruding 

from wall lining.

5.  Insert O-ring into the groove in 

the bottom of the base ring (8) 

and place over spindle/head 

works (2).

6.   Screw locking nut (7) over 

spindle/ head works (2).

7.  Place handle (9) onto spindle/

head works (2) and fasten with  

a 2.5mm hex key (11).

8.  Fit inlet connector (6) to brass 

nipple (3) and place spout (10) 

over inlet connector (6). 

 

9. Tighten with a 2.5mm hex key 

(11).

www.methven.com

Customer Care Hotline: 1300 METHVEN (638 483)

Email: [email protected]

2.5mm Allen key

Trim to 15mm 

Ø 35mm

Ø 25mm

Ø 35mm

1.

2.

3.

5.

6.

Distance from mounting stud to 

front of wall lining (ID): 

Std - 58-63mm

Ext - 63-75mm 

Hot

Col

d

Apply appropriate 

thread sealant material 

Do not discard screws

 

4.

ID

For deeper 

installations, remove 

short threaded head 

works collars and 

replace with optional 

04-9646 Spindle 

Extension Kit.

(Available separately) 

Summary of Contents for Aroha 01-9106























Reviews:

No comments

Brands by name

Popular brands

Load more brands