background image

4     Notification Appliances—PA400 Electronic Mini-Sounders and PS12/24 Series Optional Strobes

The PA400B (beige) and PA400R (red) Piezo Alert electronic sounder and
optional models PS12 and PS 24 supplementary signal strobes are
intended to be connected to the alarm Notification Appliance Circuit
(NAC) of a UL Listed 12 or 24 Volts Direct Current (VDC) Fire Alarm
Control Panel (FACP).

The sounders and strobes operate on full-wave rectified, filtered, regulated
DC voltages as well as unfiltered, unregulated DC from power supplies
UL Listed for fire alarm applications.

Table 2:  Specifications Summary

Specifications
PA400 Sounder

Operating
Voltage

9.6 VDC (absolute min.) to 33 VDC (absolute max.)

Current Drain

12 mA at 12 volts

15 mA at 24 volts

Temperature
Range

14 to 140°F (-10 to 60°C); 90% maximum RH PA400
32 to 120°F (0 to 49°C) ; 90% maximum RH with strobe added

Sound Output

Greater than 90 dBA measured in anechoic room at 10 feet, 24 volts.
For other voltages, see Figure 1.

82 dBA minimum measured in  UL reverberant room (75 dBA with strobe)

PS 12/24 Strobe
Model

PS12LO

PS12M

PS24LO

PS24M

Panel Voltage

12 VDC

12 VDC

22.5 - 30 VDC

22.5 - 30 VDC

Max.  Current
Drain @ Listed
Panel Voltage

50 mA

180 mA

25 mA

75 mA

Min.  Light
Output @
100% Viewing
Angle
(See Figure 2)

1.5 candela

15 candela

1.5 candela

15 candela

Temperature
Range

32 to 120°F (0 to 49°C); 90% maximum RH

Flash Rate

1/3 to 2 Hz

Note: The strobe cannot operate form coded power supplies, which

produce interrupted power.  The strobe must have an uninterrupted
source of power in order to operate correctly.

Model PA400

Summary of Contents for PA400













Reviews: